603904
18
Zoom out
Zoom in
Previous page
1/28
Next page
18 www.aeg.com
check that the appliance is in perfect
condition.
Positioning the cooker
The appliances are fitted with the
following parts to enable them to be
correctly positioned:
Adjustable feet, to be fitted to the
appliance, which allow the height of
the cooker to be aligned with other
kitchen furniture (fig. 4).
Backguard
1
If the cookers are
equipped with this accessory, leave of
the factory with this particular inserted
inside the packaging. In order to
install the backguard, it is necessary to
loosen the screws
2
positioned on
the back of the hob and then to fix the
backgaurd as indicated in figure 5
fig. 4
fig. 5
5.2 Gas connection
Before connecting the appliance
check that the data on the rating plate
affixed to the cooker, correspond to
those of the gas mains.
A label on the back of this handbook
and at the back of the cooker gives
the appliance adjustment conditions,
that is, the type of gas and operating
pressure.
When the final connection has been
made, it is essential that a thorough
leak test is carried out on the cooker
and installation.
Ensure that the main connection
pipe does not exert any strain on the
cooker
The appliance must be installed and
serviced by a competent person as
stated in the Gas Safety (Installation
and Use) Regulation Current Editions
and the IEE Wiring Regulations.
Any gas installation must be carried
out by a competent person (GAS SAFE
REGISTER engineer)
to the relevant Gas Standards.
The manufacturer will not accept
liability, should the above instructions
or any of the other safety instructions
incorporated in this book be ignored.
This cooker is designed to be installed
with an appliance flexible connection.
Connection is made to the RC 1/2 (1/2’
B.S.P.) female threaded located just
below the hotplate level on the rear
right-hand side of the cooker.
The gas bayonet connector can be
fitted directly behind the appliance
or alternatively adjacent to the
appliance.
If fitted in a cupboard access must be
available to disconnect and connect
the flexible hose.
It is recommended that a bayonet
type plug in micropoint flexible hose
is used.
Recommended length - 4 feet x 3/8
inch bore.
Note:
For certain types of gas bayonet
connection used, it may not be possible
for the appliance to be pushed fully back
to the wall stops.
Important:
Flexible tubing MUST comply with BS.669
Current Edition.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AEG 49190GO-MN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AEG 49190GO-MN in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AEG 49190GO-MN

AEG 49190GO-MN User Manual - Dutch - 28 pages

AEG 49190GO-MN User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info