Manual Aduro 11 eco (page 23 of 38) (English, German, Danish, French, Swedish)

711961

Zoom out

Zoom in

1/38

_______________________________________________________________________________________________________________________________

- 23 -

the wood burning stove, leading to smoke leakage and poor combustion. In these circumstances, it might be

necessary to open a window to provide air for combustion and to equalize the vacuum. Alternatively, you could fit an

air vent in the room containing the wood burning stove.

4.0 The chimney

Data for chimney calculation:

Wood

Flue temperature at [20 °C]

355

Chimney draught at testing power

[mbar]/[Pa]

0.12/12

Flue gas mass flow [g/s] 3,6

The optimum combustion is achieved at a constant chimney draught of 0.10 to 0.14 mbar measured in the flue pipe

above the stove. There are many factors that affect the chimney draught, including the outside temperature, wind

strength and surrounding buildings. If it is impossible to establish a sufficiently natural chimney draught, the chimney

can be fitted with a smoke extractor. If the chimney draught is too strong, a damper can be fitted to regulate the

chimney draught. Contact your local chimney sweep for more advice.

4.1 Inadequate draught in the chimney

If the chimney is too short, leaks or is inadequately insulated, there may be problems with the chimney draught (let

the chimney sweep assess this). The draught should be approx. 0.10–0.14 mbar in order to provide satisfactory

combustion and prevent smoke leakage.

If the chimney sweep judges the draught to be satisfactory, but you still have problems lighting a fire, try extending

the fire lighting phase/using more thin pieces of kindling, so that the chimney gets thoroughly warm. The chimney

will not draw at optimum effect until it is warm. The fire lighting phase can be prolonged by using a lot of kindling

and 1-2 firelighters. When a layer of embers has been formed, add 2–3 dry logs.

5.0 Maintaining and cleaning your wood burning stove

Gaskets

With time, the gaskets will wear, and, in order to avoid wild combustion, they must be replaced as required.

Glass

If the wood you burn is too moist, you will get soot stains on the glass pane. They can be easily removed using a

damp cloth that you dip in cold ash and rub on the sooty glass. Special cleaning agents are also available to remove

soot from glass.

Combustion chamber

The yellow tiles in the combustion chamber eventually wear out and they should be replaced when the cracks are

more that 0.5 cm. The durability of the tiles will depend on how often and how intensively the stove is used. You can

change the tiles yourself. They are available as a ready-to-use set. You can also buy one-piece tiles that you can

cut to the size of the worn plates yourself. Please consult your dealer.

Ash

Empty the ash drawer before it becomes completely full. Always leave a layer of ash on the bottom of the stove, as

this insulates the combustion chamber and makes lighting a fire easier.

Cleaning the wood burning stove

The stove’s surface is treated with a heat-resistant Senotherm® paint, which will stay at its best just by being

vacuumed with a small, soft mouthpiece or dusted with a soft, dry cloth. Do not use spirit or other solvents which will

remove the paint.

The inside of the wood burning stove and the flue pipe can be cleaned via the door and the cleaning aperture in the

flue pipe/chimney. The upper fireproof tile (the exhaust deflector) can be removed, allowing access to the top of the

wood burning stove. Cleaning of the inside of the wood burning stove and the flue pipe should be undertaken at

least once a year, or more frequently if necessary, depending on how often the wood burning stove is used. This

work can also be carried out by the chimney sweep.

Dansk | Deutsch | English | Francais | Svenska

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Aduro 11 eco in the language / languages: English, German, Danish, French, Swedish as an attachment in your email.

The manual is 0,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Aduro 11 eco Manual

Product: