Manual Adler AD 8077 (page 5 of 112) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish)

800064

Zoom out

Zoom in

1/112

IVOLTAGE PROTECTION MODE:

The device has three battery protection functions, which protect the normal operation of the refrigerator and protect the battery of the

vehicle.

The three levels of battery protection are:

H3 - high level:

for voltage 12V: stops at 10.9V and starts operation at 12.2V

for voltage 24V: stops at 23.8V and starts operation at 25.2V

H2 - medium level:

for voltage 12V: stops at 9.7V and starts operation at 11.0V

for voltage 24V: stops at 21.5V and starts operation at 22.9V

H1 - low level:

for voltage 12V: stops at 9.6V and starts operation at 10.9V

for voltage 24V: stops at 21.3V and starts operation at 22.7V

Short press "+" or "-" button to choose the function. The function is set at "H2" medium level when the refrigerator is ready for first use.

NOTE:

It is recommended to set the battery protection at H2 (medium level) when the device is used in the car.

It is recommended to set the battery protection at H2 (medium) or H1 (low) if it is external battery or backup battery.

Because of the difference in voltage output from different vehicle power supply output, if there is voltage protection (LCD display shows

F1), the battery function could be reduced to a lower one (H3 is adjusted to H2 or H1).

* Button “+” (F) is used for increasing the temperature or other settings described above.

* Button “-” (G) is used for decreasing the temperature or other settings described above.

* Power indicator (C):

-- When the refrigerator is switch on, the light is red.

-- When the refrigerator is switched off, the light goes out.

* Error indicator (D):

- If there is a failure, the buzzer will ring continuously.

- At the screen will show the fault codes.

- The error indicator (D) will be on in blue.

* LED display (E): shows

- Display the temperature and other settings.

- At the screen can be shown the fault codes as below:

F1: Voltage failure

F2: Fan current failure

F3: Compressor starting failure

F4: Minimum speed failure of compressor

F5: Controller temperature fault

E0: Broken sensor circuit

E1: Sensor short circuit

The LCD display allows you to set the temperature from -20 ℃ to + 20 ℃. The temperature actually achieved inside the device depends

on the external conditions. For example, at an ambient temperature of + 25 ℃, the lowest temperature reached inside the device is -20

℃. The device does not have a heating function.

NOTE: If the system is abnormal, check first if the battery voltage is right. If the battery voltage is right, then wait 3 minutes before you

switch on the refrigerator. If the system is still abnormal when you restart the device, then call the after service for help.

Common temperature settings for storage of:

• Wine (from +6 to +18℃)

• Vaccines, Insulin (from +2℃ till - 8℃)

• Fruit (from 4℃ till - 6℃)

• Beverage (from 2℃ till - 5℃)

• Meat (-10℃)

• Ice cream (-15℃)

Please be careful if you want to store drugs in the refrigerator. Store food in containers / bags intended for this purpose before putting

into the device.

CLEANING AND MAINTENANCE

Always unplug the device before you start cleaning.

Clean with soft, dry cloth. Do not use chemical solvents because they can cause permanent damage or deformation of the device.

TROUBLESHOOTING

Follow the troubleshooting guide below to resolve common issues.

Problem I: Unit is not functioning at all and shows no signs of power.

Possible Cause 1: Unit is not receiving power.

Solution for possible cause 1: Make sure the unit is plugged in.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 8077 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 2.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Adler AD 8077 Manual

Product: