800029

Adler AD 7730 Manual

9
Zoom out
Zoom in
Previous page
1/148
Next page
9
MONTAGE
The base (10) montage: Align the four fixing screw holes of the base (10) with the screw posts of the base (10), and screw with four self-
tapping screws to put the product into use. Look at figure 2.
PRODUCT DESCRIPTION (Figure 1)
1.Humidifed air outlet 2.Front display panel
3.Air outlet 4.Housing
5.Air inlet 6.Back cover
7.Drain cover 8.Top panels
9. Drain plug 10.The base
11.Remote control 12. Power switch
TOP PANEL & FRONT PANEL & REMOTE CONTROL MARKING – Figure 3
A. Standby button A1. Fan function indicator
B. Timer button B1.Timer indicator B2.Timer / Temperature / Cooling down count down indicator
C. Timer / Temperature increase button D. Timer / Temperature decrease button
E. Heating level regulation button E1. Low heating level indicator E2. High heating level indicator
F. Oscillation button G. Humidifier function button G1. Humidifier indicator
H. Temperature unit indicator
USAGE
1. Power on: Place the device on a stable floor and insert the plug into socket. Turn on the power switch (12) on the back of the product. “I”
means switched on, “0” means off. At this time, the device is in standby mode, the display shows ambient temperature (B2), and the
temperature unit indicator (H) will light on.
2. Fan
Press the button (A), the indicator (A1) will light up and the fan is operating (flow the air in room temperature).
3. Heating
Press the button (E) once for low-level heating ~ 1500W, the display lights up indicator (E1).
Press the button (E) twice for high-level heating 2200W, the display will light both indicators (E1 + E2).
Press the button (E) again to cancel the heating.
TIMER function: Press the button (B) repeatedly to set a period after which the device will turn itself off (between 1.0 hour – 12.0 hours, in
steps of 60 minutes). At the same time timer indicator (B1) light display.
OSCILLATION function: Press button (F) to activate oscillation, the device will swing to the right and left to distribute the exhaust air evenly.
Press again button (F) to cancel oscillation function.
TEMPERATURE ADJUSTMENT
Adjust room temperature by pressing button (D) or (C). The default setting temperature is 25°C. Temperature range from 10-35°C. Pres the
button (D) to increase the desired temperature and press the button (C) to decrease the desired temperature. The device is intelligently
programmed, it selects the working level between low or high heat according to the desired temperature and present ambient temperature.
HUMIDIFICATION FUNCTION
At first pour the water to water tank (13) according to instruction described below. To pour the water to water tank (13), unplug the device at
first. Next press down and pull outside the protrude part on the back cover (6) - look at figure 4. Take out the water tank (13) from the housing,
unscrew the plug of water tank (13) counterclockwise, pour clean water (no essential oils added) and screw the plug tightly. Put the water tank
(13) inside the housing. Set the cover properly on two latches places well and push it to close.
The humidifying function can be used normally. Plug in the device.
Press the button (G), the product turns on the humidification function, the humidification indicator (G1) lights up. Press the button (G) again to
turn off the humidification function, at the same time the humidification indicator (G1) will be off. The humidification function can also be used
separately when fan / heating function is switch off but power is on.
To drain the water out open the drain cover (7) pull the drain plug (9) and drain the reminding water to suitable tank.
When the device is not used for a long time, the water in the tank should be drained.
Applicable environment conditions for the device operation:
- heating function use temperature in range from -20°C to 25°C.
- humidifier function use in temperature in range from 5°C to 40°C and the relative humidity less than 80%.
To turn off the device press the button (A) again. Then, the fan will cool down the heating element inside the housing during 30 seconds, next
the fan will automatic turn off. If the device is not set on heating function before, it will go directly to standby.
Lighting off of the front display panel (2): After the device is working for 10 minutes, it will automatically enter the light off screen mode, press
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 7730 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 7730 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info