734443

Adler AD 5032 Manual

5
Zoom out
Zoom in
Previous page
1/100
Next page
sure that the steam control switch (C) is in the “0” position.
3. When the iron reaches the required temperature, the heating indicator light (H) will turn off.
4. After use, turn the temperature control knob (I) to the “OFF” position.
5. Remove the plug from the wall socket.
SPRAYING FUNCTION
1. Fill the water tank with water as described in “Filling with water”.
2. Press water spray button (D).
3. Note: No matter what steam ironing of dry ironing is, spray will always be available in any case.
STEAM IRONING FUNCTION
1. Fill the water tank with water as described in “Filling with water”.
2. Plug in. The power/heating indicator lights (M / H) will turn on.
3. Turn the temperature control knob (I) clockwise to the “MAX” position. Do not turn the switch to” N” or “O” for steam ironing.
4. When the iron reaches the required temperature, the heating indicator light (H) will turn off.
5. Adjust the steaming by moving the steam control switch (C).
6. After use, turn the temperature control knob (I) to the “OFF” position.
7. Remove the plug from the wall socket.
8. After each use, make sure that the water tank is empty.
Caution: Do not steam ironing synthetic fabrics, nylon, synthetic silk or silk fabrics. Steam can ruin the texture of the fabric.
BURST OF STEAM FUNCTION
This function will be able to provide more steam to remove stubborn creases.
1. Set the temperature control knob (I) to MAX until the indicator light (H) goes off.
2. Release the steam by pressing the steam button (E).
3. Wait for several minutes and let the steam penetrate through the fabric, and then release more steam through pressing this
button again.
Note:
1. There should be 3-5 seconds rest between two times of pressing Steam burst button (E) in order to obtain the best steaming result.
2. Fill the water to the MAX position before using this function.
3. In order to prevent the water leaking from soleplate, please do not press the steam burst button (E) continuously with more than 5
seconds.
VERTICAL STEAM IRONING FUNCTION
The vertical steam ironing system allows you to use the iron for vertical ironing. This is especially useful for getting wrinkles out of hanging
clothes, curtains.
1. Fill the water tank with water as described in “Filling with water”.
2. Plug in. The power/heating indicator lights (M/H) will turn on.
3. Turn the temperature control knob (I) to the “MAX” position. Do not turn the switch to” N” or “O” for steam ironing.
4. When the iron reaches the required temperature, the heating indicator light (H) will turn off.
5. Adjust the steaming by moving the steam control switch (C).
6. Hang the garment on a clothes’ hanger and pull the garment tight with one hand.
7. Hold the iron in vertical position with the other hand and press the steam burst button (E) to iron the garment. Touch the
garment lightly with the soleplate of the iron to remove creases.
8. After use, turn the temperature control knob (I) switch to the “OFF” position.
9. Remove the plug from the wall socket.
10. After each use, make sure that the water tank is empty.
11. Caution: Do not use steam ironing on clothes or fabrics that are wearing people or animals. The temperature is too high.
SELF-CLEANING SYSTEM
Note: Before you start the self-cleaning procedure, make sure the iron is not plugged in and the steam control (C) is in the “0” position.
1. Fill the water tank with water up to “MAX”. Do not use vinegar or other descaling liquids in the water tank.
2. Plug in and turn the temperature control knob (I) to the “MAX” position. The power / heating indicator lights (M/H) will turn on.
3. When the heating indicator light (H) turns off, unplug.
4. Hold the iron in a horizontal position above the sink. Press and hold the Self-Clean button (J).
5. Steam and boiling water will start to come out of the iron plate holes, which contain salts and minerals that have been
accumulated in the steam chamber from previous uses.
6. Gently move the iron back and forth until the water tank is empty.
Caution: The water that comes out during self-cleaning is very hot. Be very careful not to fall on you.
7. When the water tank is empty, release the self-clean button.
8. Allow the iron to cool down completely.
9. Wipe the soleplate with a cold damp cloth.
ANTI-CALC SYSTEM
A special filter inside the water tank softens the water and prevents scale build-up in the soleplate. The filter is permanent and does not
5
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Adler AD 5032 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Adler AD 5032 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 3,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info