755222
79
Zoom out
Zoom in
Previous page
1/116
Next page
Chapter III – Installation instructions – Event codes
73
You can press one of the following keys to reach
particular events. You have to wait a little for the
display.
1 Alarms
2 24-hour alarms
3 Fire alarms
4 Panic alarms
5 Zone tamper
6 User codes
7 Set Partitions
8 Unset Partitions
9 Entry
Press 0 to go to a fixed position in the list.
2.52.2 Option 93-2: Print Log
e.g. 0020
If a printer is connected to the alarm centre, you
can print some or all events of the event list.
Select the number of events you want to print
and press . Then specify the event number
where you want to start printing. For example, if
you want to print 10 events starting at event 40,
events 40 to 49 are printed. More than one line
may be needed for an event.
To end the current print job, select this option
again and specify 0 for the number of events to
be printed.
After you use the “Print Log” option once, the
system goes into online print mode. Switch off
the printer to stop printing.
2.52.3 Option 93-3: View Access Log
The access memory stores every type of access
that uses the user code. Press or to scroll
through the list ( shows earlier events).
2.52.4 Option 93-4: Print Access Log
This access log stores every entry of the access
type user code (see operating instructions).
Press or to scroll through the list (
shows earlier events).
2.52.5 Option 93-5: System Print
Select this option to print details of alarm centre
settings. The following options are available:
1 – Configuration
Prints details of all general, DD243, and
EN50131 settings (see pages 48, 51, 52).
2 – Users
For the engineer and every installed user, the
user number, name, type, partitions and assigned
menus are printed.
3 – Zones
For every defined zone, the zone number, type,
partitions, name, attributes and resistance values
are printed.
2.53 Event codes
Event Description
--- NO EVENT --- Not used
### LECS or REMS The number of operating panels connected to the system
### NODE R# ADD Operating panel added to a wired auxiliary.
# Bus number, ## Auxiliary number, R# Operating panel number
### NODE R# LOST Operating panel R# was removed from the wired auxiliary.
### NODE R# TAMP Tamper alarm triggered by operating panel R#.
### NODE'S Number of connected auxiliaries
Configuration 1
Print : No
Log Functions 5
System Print
Users 2
Print : No
How many events?
0030
Log Functions 2
Print Log
With offset of:-
0040
79


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus Terxon LX - AZ4200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus Terxon LX - AZ4200 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus Terxon LX - AZ4200

Abus Terxon LX - AZ4200 User Manual - English - 16 pages

Abus Terxon LX - AZ4200 Installation Guide - German - 31 pages

Abus Terxon LX - AZ4200 User Manual - German - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info