554031
88
Zoom out
Zoom in
Previous page
1/96
Next page
11-88
Chapter 11 Brief guide
This chapter explains the installation steps shown on the DVD for the ABUS wireless alarm package including a smoke detector. After
you have taken the installation steps shown in this guide, your ABUS wireless alarm system is completely operational.
11.1 Hardware installation
11.1.1 ABUS wireless alarm system
Install the ABUS wireless alarm system in a suitable place in your object.
Plug the power supply unit into the
AC socket of the wireless alarm system. Do not plug in the mains plug yet.
Connect the telephone line with either a RJ11 telephone plug or two loose cables to the telephone connector of the
system (Line).
Place the standby batteries provided in the battery holder and then plug this into the wireless alarm system.
Plug the jumper plug of jumper
J10 on the main board on to both pins to charge the batteries.
Now plug the power supply unit into the mains socket.
The wireless alarm system starts up and soon reports “System is on”. If not, check that the power supply unit is plugged in, that
there is current at the mains socket, and the power supply unit plug is correctly plugged into the wireless alarm system. The fault
LED flashes since the time and date have not yet been entered and the batteries are not fully charged. The batteries should be
fully charged after 12 hours.
If the system issues an audible alarm when it is switched on, the tamper contact may not be properly pressed. In this case, do
the following:
Enter the factory default
Grand Master PIN on the system keypad:
11
22
33
44
Press the “
Disarm button:
The ABUS wireless alarm system is now ready for programming.
11.1.2 Wireless opening detector
Install the wireless opening detector at the top centre of the door to be monitored. The magnet is fixed to the movable part of
the door. The magnet and the opening detector must be arranged parallel to each other.
Insert the battery supplied (check polarity!).
The red LED of the detector lights up.
If not, check that the battery is correctly inserted and measure the battery voltage, which must be above 2.8V.
Press in the spring of the detector and close the door.
When you open the door, the LED lights up again.
Wait until the LED switches off, then close the door.
The LED must light up again. If not, the magnet and the transmitter are incorrectly positioned or too far apart.
11.1.3 Wireless motion detector
Install the wireless motion sensor in the corner of a room with a terrace or balcony. The sensor must point into the room and
should not be directed towards large window areas. The red LED of the detector faces up.
IMPORTANT: The infrared detector reacts to heat movement. Therefore, do not point the sensor to fan heaters or other heat
sources. Pets such as cats and dogs can also trigger the detector.
Insert the battery supplied (check polarity!).
The red LED of the detector lights up.
If not, check that the battery is correctly inserted and measure the battery voltage, which must be above 2.8V.
11.1.4 Wireless smoke detector
Install the wireless smoke detector in the centre of your bedroom ceiling. Further smoke detectors should be fitted in the living
room and the entrance hall. Smoke always rises first to the highest point of the room.
IMPORTANT: Thick cigarette smoke or water vapour (steam) can trigger the detector.
Insert the two batteries supplied (check polarity!) and press the test button. Keep the button pressed until the smoke detector
issues a long beep.
If it does not, remove the batteries and wait 30 seconds. Insert the batteries again and repeat the test.
If it fails again, measure the voltage of both batteries. It must be above 2.8V.
Remove the batteries.
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus FU9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus FU9000 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus FU9000

Abus FU9000 User Manual - English - 56 pages

Abus FU9000 Installation Guide - German - 96 pages

Abus FU9000 User Manual - German - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info