554031
20
Zoom out
Zoom in
Previous page
1/96
Next page
6-20
6.7 What are the effects of the different jumper settings?
The PC board of the ABUS wireless alarm system is fitted with internal jumpers. Configure the jumpers according to the function
required as shown in this table:
Jumpers on the
mainboard
Position Function
The
J9 jumper of the ABUS wireless alarm system is used for restoring the
default factory settings of your alarm system.
To restore the factory settings, plug the jumper plug on to both pins of the
jumper. Switch off all electricity to the system and wait at least 10 seconds.
Reconnect the power supply. The factory settings are restored. You can then
take off the jumper plug and plug it on to one pin.
IMPORTANT: Restoring the factory settings is possible only if it was
enabled in the installer menu.
Restores the factory
settings.
(J9)
(Default)
The default position of the jumper plug
Jumper
J10 of the ABUS wireless alarm system is used for selecting
between rechargeable batteries and normal batteries. If the jumper plug is
plugged on to both pins, the batteries are recharged.
IMPORTANT: As this is not the factory settings, this jumper position
must be changed.
Rechargeable battery
(J10)
(Default)
Use this setting for batteries that cannot be recharged.
Jumper J6 of the ABUS wireless alarm system activates/deactivates the
battery discharge protection. If the jumper plug is placed on to one pin, your
alarm system switches off automatically if the battery voltage falls below 6.3V
DC to avoid excess discharge.
NOTE:
With this setting, your alarm system first starts to operate when power is
available from the power supply unit.
Battery protection
(J6)
(Default)
The battery discharge protection is deactivated, i.e., the battery can
be completely discharged if there is a mains power failure, so that
the batteries have to be replaced.
NOTE:
With this setting, alarm system first starts to operate when the batteries are
inserted.
Jumpers on the
base plate
Position Function
UO 1 (J5)
or
UO 2 (J5)
(Default)
Defines the function of switch output 1 and switch output 2, as described in
the section “wired utility outputs” on page 5-17.
Default:
1 pin
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus FU9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus FU9000 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus FU9000

Abus FU9000 User Manual - English - 56 pages

Abus FU9000 Installation Guide - German - 96 pages

Abus FU9000 User Manual - German - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info