554031
18
Zoom out
Zoom in
Previous page
1/96
Next page
6-18
NOTE:
1. You can connect external equipment to clamp N.O instead of to clamp N.C.
If you connect to clamp NC (normally closed), the circuit between the system and an external device is
closed. If the switch output is activated, the system interrupts the circuit and the connected device is
switched off.
If you connect to clamp NO (normally open), the circuit between the system and an external device is
interrupted. If the switch output is activated, the system closes the circuit and the connected device is
switched on.
2. The “COM/BLK” and “AUX/RED” clamps are collective clamps. You can connect more than one cable to
them.
Connect transistor outputs UO3 (switch output 3) and UO4 (switch output 4) as follows:
Connect the positive connector of the external device you want to control with “AUX /RED(+) clamp and the negative with the
clamp of the switch output UO3 (or UO4).
6.5.4 Connecting a device ground
The grounding (earth) protects your electronic equipment against damage and interference caused by lightning and inductive
voltages.
An ideal grounding is the earth connection (green/yellow wire) in the power socket.
Important: Never connect 230V directly to the system. Only the earth!
Connecting to ground:
Make a connection between the earth contact of the ABUS wireless alarm system and an electrical earth connection to
protect it against lightning and static electricity.
!
IMPORTANT NOTE:
The earth contact must be made in accordance with local regulations.
6.5.5 Connecting a wired zone
The ABUS wireless alarm system has a wired zone – Zone 33 (Z33), which can be used, for example, to connect a key switch or
a panic emergency call. Connect this zone using twisted-pair cables or a 4-core cable. The following figure shows the different zone
connection types – these have to be programmed accordingly in the installer menu later:
NOTE:
The wired zone cannot be used as a fire zone. For a zone with tamper, you can use a double terminal resistor (DEOL) to
save additional connections.
6.5.6 Connecting an external consumer
Use the collective clamps AUX/Red (+) and COM BLK (-), to connect external devices or detectors that require a power supply of
9V DC with a maximum power consumption of 200mA.
!
IMPORTANT:
During a power failure, the AUX output is deactivated to ensure a longer system runtime.
NOTES:
The total current of collective clamps should not exceed 200mA.
If the collective output is overloaded (more than 200 mA) and it is silenced, you have to interrupt the load at the output
for at least 10 seconds before reconnecting a load to the collective output.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abus FU9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abus FU9000 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abus FU9000

Abus FU9000 User Manual - English - 56 pages

Abus FU9000 Installation Guide - German - 96 pages

Abus FU9000 User Manual - German - 55 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info