677186

Abilia 425718 - Gewa Control 18 Manual

27
Zoom out
Zoom in
Previous page
1/60
Next page
27
Recording IR Channels from another Transmitter
Make sure the batteries in both transmitters are fully charged. Do not use the transmitters in
intense light (e.g., sunlight) when programming.
Place the two transmitters on a table with the original transmitter directed towards the rear
of your Control 18, see picture.
1. Choose the level where the channels are to be recorded with
---
. Only one level at a time can be programmed.
2. Press
P
and
1
at the same time. The indication lamp on
button 1 and the present level now flashes.
To check that the transmitters are in the right position, keep
any button pressed on the original transmitter. The indication
lamp for the Level-button now flashes green. Move the
original transmitter to the left or to the right until the
indication lamp goes out. Then move the original transmitter
backwards until the indication lamp goes out (one meter for
certain transmitters). Place the original transmitter centrally
between these positions. Certain types of transmitters only
emit a short flash each time the button is pressed. In these
cases, press several times.
3. Press and release the button
X
on Control 18, which is to
be programmed. The indication lamp for the Level-button
now emits a steady orange light.
4. Keep the corresponding button
Y
on the original transmitter
pressed. Release the button when the indication lamp for the
Level-button goes green. It might take up to 10 seconds.
If the indication lamp goes orange again press the button
one or more times until the light flashes green and goes out.
If the indication lamp flashes red the programming has failed.
Try once more from step 2.
If a beep is heard
the level is locked and no
programming can be made. See section Locking/Unlocking
the Settings Lock how to unlock a level.
5. If the programming of the first button was successful, repeat
steps 3 and 4 until all buttons are programmed. Finish by
pressing
---
.
6. The light for the Level-button flashes green to indicate that
the programming is complete.
7. Now test the programmed functions on the device which is to
be controlled.
Recording IR Channels
Press
P
+
1
, select button
X
, select button
Y
, then continue or finish with
---
.
Important! When just one level is used, the Level-button automatically becomes the next
levels first button, see Table 1. It means that it is possible to record an IR channel on the
Level-button, but only when just one level is being used.
Original transmitter
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abilia 425718 - Gewa Control 18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abilia 425718 - Gewa Control 18 in the language / languages: English, Swedish, Norwegian as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abilia 425718 - Gewa Control 18

Abilia 425718 - Gewa Control 18 User Manual - German, French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info