677187

Abilia 425710 - Gewa Control 10 Manual

27
Zoom out
Zoom in
Previous page
1/56
Next page
27
Tip! Control 10 can record codes from most IR transmitters on the market with a few
exceptions. You may have problems with a few or all of the functions for a certain IR
transmitter. In these cases it is possible to try another recording method. Instead, do as
follows in step 2; Press
P
and
1
at the same time but keep them pressed for
approximately 2 seconds until the indication lamp for programming flashes green and goes
out. Control 10 is now in another recording mode. Otherwise use the same recording
procedure as above.
Adding a 4096-code
Control 10 is delivered with a special coded channel (4096) on the Code-button
!
. The
code is selected randomly. This coded channel is normally used for functions that require
strict authorization such as apartment or house doors. The code has 4096 different
combinations and has always the same code irrespective of which level you use. If you
have to program a new coded channel there are two methods of doing so.
Method one: record the code from another transmitter, as described under Recording IR
channels from another Transmitter. By this method it's possible to program a coded channel
on any button independently of level.
Method two: Enter a binary code. The binary code will always be associated with the Code-
button
!
and it is the same for all levels. Make up your own binary code or use the code
already programmed in an IR receiver or transmitter.
There are two types of IR receivers: an older type of receiver where you set the code with a
12-pole switch, or a newer type where the IR receiver is programmable. The principle is the
same when it comes to creating the binary code. Fig 3 shows a 12-pole switch. Switches 1,
4, 6 and 12 are in the “On” position, the others are in the “Off” position.
1 2 3 4 5 6 7 8 9 10 11 12
2048 1024 512 256 128 64 32 16 8 4 2 1
On
Off
Fig 3
The following example describes how the binary code is created.
1. Press
P
and
!
at the same time. The indication lamp for the current level are now lit.
2. Enter the code by pressing on
---
or
!
.
---
= switch in Off position and
!
= switch in On position.
Press twelve times in turn;
!
,
---
,
---
,
!
,
---
,
!
,
---
,
---
,
---
,
---
,
---
,
!
, (Fig 3).
3. When you have pressed twelve times the indication lamp for programming flashes green
to show that the operation is finished.
The code is now programmed on the
!
-button. Make a note of the chosen code for
future usage.
Adding a 4096 code
Press
P
+
!
, press
---
or
!
12 times.
---
= Off position.
!
= On position.
Default setting: Random code
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Abilia 425710 - Gewa Control 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Abilia 425710 - Gewa Control 10 in the language / languages: English, Swedish, Norwegian as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Abilia 425710 - Gewa Control 10

Abilia 425710 - Gewa Control 10 User Manual - German, French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info