Manual AAS Strum Electric GS-1 (page 52 of 98) (English)

541315

Zoom out

Zoom in

1/98

52 Parameters

6.3 The Ampliﬁer Module

Strum Electric is equipped with a versatile 2-channel ampliﬁer with speaker cabinet and spring

reverb. With relatively few parameters, this ampliﬁer module allows one to obtain a rich variety of

sounds for different music styles.

The ampliﬁer section of this module is switched on or off using the ﬁrst On button located at

the top of the module. The Channel selector allows one to switch between the two channels of

the ampliﬁer. Channel one offers clean to semi-dirty sound while channel two is well-suited when

strong distortion is required. The Drive knob is used to adjust the amount of distortion in the sound.

The sound becomes more and more distorted as the knob is turned clockwise. The Mid knob is

used to set the amount of mid-range frequencies in the sound. In its middle position, the sound is

not modiﬁed, mids are cut or boosted by up to ±12 dB by turning this knob to the left or right. The

Level knob is a gain knob which is used to adjust the overall volume of the ampliﬁer. Note that the

effect of this control on the frequency response of the ampliﬁer is different for each channel.

The Low and High parameters are used to boost or cut low and high frequencies respectively

by up to pm 18dB by turning the knob from its center position. These controls have a similar

behavior for both channels. Additional control on the frequency response is obtained by using the

Byte control which is switched on or off by clicking on the B button next to the channel selector.

This parameter boosts high frequencies while cutting some low frequencies for a brighter sound.

The second On button is used to switch on or off the spring reverb. The Spring knob is used

to set the amount of wet signal in the mix, turning the knob clockwise increasing the amount of

reverberation in the signal.

Finally, the speaker cabinet is switched on or off by clicking on the last On button in the upper

right corner of the module. This part of the module simulates the effect of both the speaker and the

cabinet on the frequency response of the ampliﬁer module. The back of the cabinet can be open or

closed using the O and C button of the Cabinet selector. Opening the back of the cabinet allows

waves to travel from the back of the cabinet and interfere with those traveling from the front part

of the cabinet resulting in a more colored sound.

The low-cut (or high-pass) ﬁlter is used to remove from the output sound of the instrument

frequency components below the cut-off frequency. The cut-off frequency of the ﬁlter is increased

by turning the knob clockwise. when this knob is in its leftmost position, the ﬁlter has no effect on

the sound.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AAS Strum Electric GS-1 in the language / languages: English as an attachment in your email.

The manual is 2,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AAS Strum Electric GS-1 Manual

Product: