Manual AA-Drill 77350-1 (page 20 of 36) (English, German, Dutch, French)

621600

Zoom out

Zoom in

1/36

d. When drilling hold on the handle at the right side of the head frame and press

downward.

8. MAINTENANCE

Regular maintenance increases the life of your drill press.

After using the machine you have to clean it completely and lubricate all sliding

and moving parts.

Table adjustments:

a. To adjust table up or down, loosen clamp bolt

A). Then turn crank handle (B) to desired

height. Retighten clamp bolt (A) before drilling

operations.

b. To swing table 360° loosen clamp bolt (A) then

swing table to appropriate position, re-tighten

clamp bolt. For long work pieces swing table

180° and use the base as your table.

c. To tilt table loosen work table nuts (C), tilt to

desired angle and re-tighten nuts.

Spindle adjustments:

Workpiece method (Fig. 19, 20) recommended for drilling a specific depth which

can be marked on the side of the workpiece.

1. Mark the depth of the hole on the side of the workpiece (1).

2. Turn off the drill press, bring down the drill bit (2) until the tip is even with the

mark.

3. Hold the feed handle and spin the lower nut (3) down to contact the depth stop

lug (6) on the head.

4. Spin the upper nut (5) down and tighten against the lower nut (3).

5. Release the feed handle and now the drill bit will be stopped

after travelling downward the distance marked.

Depth scale method (Fig. 20) recommended for drilling a known depth hole.

1. Turn off the drill press, turn feed handle until the depth stop (6) points to the

desired depth on the depth scale (4). Hold the feed handles in that position.

2. Spin the lower stop nut (3) down to contact the depth stop (6).

3. Spin the upper stop nut (5) against the lower stop nut (3)and tighten.

4. The drill bit will not stop after traveling the distance on the depth scale.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of AA-Drill 77350-1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

AA-Drill 77350-1 Manual

Product: