503238
51
Zoom out
Zoom in
Previous page
1/96
Next page
Instruction manual ADMR 51
gis
9 Starting and running
9.1 Starting and running
Start the appliance as follows:
1. Fill the appliance (5 "Filling")
.
2. Open (3.5 "Installation diagram")
the manual gas
valve.
3. Switch on the power to the appliance using the
isolator between the appliance and the power
supply.
4. Switch the electronic controller ON by setting the
ON/OFF switch to position I.
The display will now show
INTERNAL CHECK
for
about 10 seconds and go to the main menu.
5. Press the blue arrow once ( ) to position the
cursor in front of
ON
and press . The
display shown in the figure will appear.
6. Confirm the
START OPERATION
by pressing
.
The appliance is now in "ON mode". If there is a
heat demand, the appliance will run through the
heating cycle (2.3 "The appliance's heating
cycle").
If the heating cycle is not run, there is no heat
demand; if this is the case, Tset will probably need
to be set (11.3 "Setting the water temperature").
9.2 The appliance's heating cycle
The appliance's heating cycle is activated as soon as
the measured water temperature (T
net
) falls below the
threshold value (T
set
). This threshold value depends
on the currently selected appliance operating mode.
For example, if the appliance is in "OFF mode" (frost
protection), then this value is 5 °C. If the appliance is
in "ON mode", then this threshold value is selectable,
for example, 65 °C.
The heating cycle runs in turn through the following
states:
1. HEAT DEMAND
2. WAITING TIME
3. FLUE DAMPER
4. PRE-GLOW
5. IGNITION
6. RUNNING
7. WAITING TIME
The complete cycle is explained in the following
example, which assumes the appliance is in the basic
mode
ON
.
Note
The same heating cycle applies to the other
operating modes.
Once the appliance starts, it will run through the
following steps:
1. The water temperature drops below the set
temperature of (for example)
65
°C. The
electronic controller detects a demand and starts
the heating cycle.
- The icon is activated.
- The message
HEAT DEMAND
appears.
2. Following demand, the waiting time starts. The
waiting time lasts approximately 12 seconds.
- The icon is activated.
- The message
WAITING TIME
appears.
INTERNAL CHECK
MENU
»OFF
^ ON
È WEEK PROGRAM
»START OPERATION
^ CHANGE SETPOINT
È Tset=65ÉC
ON Ê
13:45 Thursday 63ÉC
Tset 65ÉC
HEAT DEMAND
ON Ê Ê
13:45 Thursday 63ÉC
Tset 65ÉC
WAITING TIME
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith ADMR135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith ADMR135 in the language / languages: English as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith ADMR135

A.O. Smith ADMR135 User Manual - Dutch - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info