503290
45
Zoom out
Zoom in
Previous page
1/64
Next page
Instruction manual ADM 45
gis
9 Starting and running
9.1 Introduction
Topics covered in this chapter, in sequence:
Starting the appliance;
The appliance's heating cycle
.
9.2 Starting the appliance
Start the appliance as follows:
1. Fill the appliance (5 "
Filling").
2. Open (3.5 "
Installation diagram") the manual gas
valve.
3. Switch on the power to the appliance using the
isolator between the appliance and the power
supply.
4. Begin the ignition procedure by pressing and
holding the white button (1) on the gas control
while repeatedly pressing the piezo igniter (2) until
the pilot flame ignites. See the figure. The pilot
flame can be seen through the inspection window
above the burner tray.
Gas control
5. Keep the white button pressed in for about 30
seconds before carefully releasing it. The pilot
flame should now stay lit.
6. Set the appliance in the "ON" mode by setting the
on/off switch on the control panel to position I.
7. Using the control thermostat (7.3 "
Control
thermostat"), set the desired water temperature.
If there is a heat demand, the appliance will run
through the heating cycle (9.3 "
The appliance's
heating cycle").
Warning
If the pilot flame goes out during the heating cycle
or ignition procedure, you must wait 5 minutes before
repeating the ignition procedure.
9.3 The appliance's heating cycle
The appliance's heating cycle is activated when the
measured water temperature (T
water
) falls below the
threshold value (T
set
). T
set
can be adjusted using the
control thermostat, for example position 3 (± 60 °C).
The heating cycle runs successively through the
following states:
1. HEAT DEMAND;
2. IGNITION;
3. RUNNING.
The complete cycle is explained in the example set out
below.
1. The control thermostat sensor measures the water
temperature (T
water
). If T
water
drops below the set
temperature (T
set
), there is demand and the
control thermostat will close. This will cause the
gas control to open.
2. Once the gas control is open, the pilot burner will
ignite the gas flow.
3. The appliance is now running. This means that
actual heating has started. When the water
reaches the set temperature, the demand ceases.
The gas control closes and the burner tray is
extinguished (the pilot flame stays lit).
4. The appliance is now said to be in an idle state,
waiting until T
water
once again falls below T
set
.
With any subsequent heat demand, the heating cycle
will resume from step 1.
3
1
2
IMD-0195 R1
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for A.O. Smith ADM 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of A.O. Smith ADM 50 in the language / languages: English as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of A.O. Smith ADM 50

A.O. Smith ADM 50 Usermanual and installation guide - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info