42029

9ZAP 9Z World Champion Model 2 Manual

27
Zoom out
Zoom in
Previous page
1/29
Next page
24
D
ESCRIPTION
O
F
N
EW
F
UNCTIONS
Idling area
Point 1 is the stick maximum slow area. Therefore, adjust the idling mixture so that a
good idling speed is obtained. If the carburetor is still flooded when point 1 is 0%,
raise throttle curve point 1~2 and increase the air and readjust the throttle trimmer.
Set a value so that points 2 and 3 are connected to the hovering area.
Hovering area
Points 4~6 are the hovering area. Slowly hover and adjust the mixture while observ-
ing the hovering state. After hovering adjustment, land and take off and perform
climb adjustment. Next slowly climb from hovering and perform climb adjustment.
Adjust for the desired response so that the carburetor is not flooded within the points
4~6 range.
Flying range
Points 7~9 are the flying range. Point 9 is the maximum speed needle. Therefore,
adjust the connection from hovering to maximum speed with points 7 and 8. Slowly
set the throttle stick from hovering to full close and adjust the high side mixture. With
the stick fully closed, fly at high speed and set the needle, while paying attention to
the change in the sound. Finally, carry out hovering and flying adjustment and finish
by fine adjusting to the best mixture. When flying, the entire high side can be con-
trolled based on point 5 and needle changes caused by temperature changes can be
adapted to by using the VR set with the model menu (MDL) fuel mixture (FMC)
item.
5 Condition setup
(1) When the condition menu (CND) is called and the fuel mixture "FMC" function is
selected, the FUEL MIX item is displayed.
-This item enables setting of each condition. Set each condition matched to the number of conditions used.
CAUTION: Conditions setting is a condition.
(2) Set MST MIX MODE (master mix mode).
-This mode operates by mixing throttle and mixture. However, what is operated is decided individually. Usually,
this is used with "MIXED".
-When used with "MIXED", when the throttle curve is set, the mixture curve is simultaneously mixed and
changed. (The mixture curve can also be set in the mix mode "MIXED".)
-When used with "UNMIXED", throttle and mixture control are set independently. When a tuned silencer is used,
etc., the fuel can be adjusted independently and the adjustment width is widened. Since all mixture adjustments
are carried out independently, learn the functions before trying to make any adjustments.
(3) Set the mixture curve with the POINT item.
-Nine points, from point 1 to point 9, can be set. The smaller displayed value is the direction in which the needle
is closed and the larger displayed value is the direction in which the needle is opened.
-Set the basic curve data by referring to the values shown below. However, this setting is a little dense.
Reference values (OS carburetor)
(4) The setting range is divided into an idling area, hovering area, and flying area.
Point P1 P2 P3 P4 P5 P6 P7 P8 P9
Set value (%) 15 36 50 58 64 68 73 76 80
… 27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 9ZAP 9Z World Champion Model 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 9ZAP 9Z World Champion Model 2 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info