42029

9ZAP 9Z World Champion Model 2 Manual

25
Zoom out
Zoom in
Previous page
1/29
Next page
22
D
ESCRIPTION
O
F
N
EW
F
UNCTIONS
FUEL MIXTURE FUNCTION SETUP EXAMPLE
Helicopter
This function is used by mixing the throttle (CH3) and needle (CH8) channels.
1 Basic curve
This fuel mixture basic curve is set for model NO.10. Use it as reference.
Reference curve values (OS carburetor)
Point P1 P2 P3 P4 P5 P6 P7 P8 P9
Setting (%)153650586468737680
-This curve becomes the data with a differential given to the low/high side of the throttle channel with the ATV
function.
-When this curve is changed, throttle (CH3) of the ATV function in the condition menu is set.
-The ATV function settings are RATE "A" 80% and RATE" 100%. Since these values can differ slightly with the
engine, fuselage, and fuel used, they are finally set individually.
2 Servo and carburetor linkage
(1) When connecting the linkage, read this section together with the carburetor in-
struction manual.
(2) Set function control (FNC) of the AU2 channel to match the application.
-Call function control (FNC) and select AU2.
-If the high side mixture (needle) is controlled while the model is flying, switch to VR setting. (However, do not
duplicate the functions.)
-If high side mixture (needle) control while flying consists of curve setting only, the setting can be left in the initial
setting SW "C" state. (Set the switch to the desired position.)
(3) In this stage, the fuel mixture function operates as a channel. Therefore, use the
VR or switch set in item (2) above to set the operation direction and operation
amount.
-Connect the AU2 (CH8) servo to the mixture control arm.
-When using a VR, when a dial VR is turned clockwise, or a slide VR is pushed down, the needle is closed. (Use
the reverse function to set the operation direction.)
(4) The length of the servo horn used can be set to 16.5mm (servo horn A) and the
ATV setting can be set to about 100%.
-Trim at the A and B sides of ATV AU2.
(5) When the throttle stick is in the center as shown in the figure, connect the mixture
control side linkage so that the linkage rod and horn and arm are perpendicular.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 9ZAP 9Z World Champion Model 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 9ZAP 9Z World Champion Model 2 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info