5597
22
Zoom out
Zoom in
Previous page
1/38
Next page
© 3M 1999 3M
Multimedia Projector MP8780
ENGLISH
21
Section 7: Troubleshooting
Error Message Displays
NO SIGNAL IS
DETECTED.
INVALID.
CHANGE THE LAMP.
LIFE: 50 HS
CHANGE THE LAMP.
NO LIFE.
Cause
The projector is not detecting a signal.
The horizontal frequency of input signal
exceeds projector capability.
Lamp operation time is greater than 950
hours.
Lamp operation time is greater than 1,000
Solution
Check cable connections to input device. Input device not
connected to this input mode, switch to next mode.
Switch projector to correct resolution.
See Appendix A.5
Change the projector lamp and reset the lamp operation
hours to zero.
Change the projection lamp and reset the lamp operation
hours to zero.
7.2 Message/Solution Table
Symptom Cause Solution
Power cannot be The Main power is not turned on. Turn the MAIN POWER switch on.
turned on. The power cord is disconnected. Insert the power cord into an AC socket.
90 seconds have not elapsed since Wait 90 seconds before turning on power.
the power was turned off.
No picture and sound. The setting of the input source is not Set the correct input using the input select button of
correct. the projector or the remote control.
RGB/Video/Audio wiring to projector is Connect the cable to correct input/output source.
not correct.
Sound is heard with no RGB/Video/Audio wiring to projector Connect the cable to correct input/output source.
picture. is not correct.
Lens cap is on. Remove lens cap.
Picture is displayed with Audio wiring to projector is not correct. Connect the cable to correct input/output source.
no sound. The volume is set to minimum. Press the VOL button to increase Volume.
The unit is muted. Press the MUTE button.
Color is weak and tint is The color and tint have been adjusted • Adjust the color and tint correctly.
incorrect. incorrectly.
Picture is dark. The brightness and contrast has not Adjust the brightness and contrast correctly.
been adjusted incorrectly.
The lamp needs to be replaced. Replace the lamp with a new one.
Picture is not clear Projector is out of focus. • Adjust the focus and PHASE.
LAMP indicator lights Lamp will not ignite.
• Turn off power and let cool for 20 minutes, then restart.
red.
• If problem persists call your dealer.
Cover indicator red. Air filter door on bottom of case
• Ensure air filter door is closed.
is open.
TEMP indicator Temperature inside projector • Clear blocked ventilation holes.
red. is too hot. Clean air filter.
7.1 Symptom/Solution Table
Downloaded From projector-manual.com 3M Manuals
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m MP8780 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m MP8780 in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of 3m MP8780

3m MP8780 User Manual - German - 22 pages

3m MP8780 User Manual - Dutch - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info