5597
21
Zoom out
Zoom in
Previous page
1/38
Next page
3M
Multimedia Projector MP8780 © 3M 1999
ENGLISH
20
Note
For maximum lamp life, do not apply shock, handle or scratch the lamp glass when it is hot. Also, do not use
an old or previously used lamp as a replacement lamp.
1. Loosen cover retaining screws: The lamp access cover is located on the side of the projector. Use a
screwdriver to uncrew the retaining screws (1) on the left and right side of the cover.
2. Remove lamp cover: Press the spring tabs on each side of the cover and gently remove the lamp
cover (3).
3. Loosen lamp retaining screws: Use a screwdriver to unscrew the lamp module retaining screws (4).
4. Remove lamp module: Carefully slide the lamp module out (5) of the projector.
5. Insert lamp module: Carefully insert the new lamp module (5). Ensure that it is fully seated. Tighten the
lamp module retaining screws (4) to secure the lamp module in place.
6. Insert lamp cover: Position the lamp cover and depress the spring tabs (2) on each side of the cover to
lock it in place.
7. Tighten retaining screw: Tighten the cover retaining screws (1) to the cover. After replacing the projection
lamp, always reset the lamp operation hours to zero.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
To reduce the risk of cuts to fingers and damage to internal components, use caution when removing lamp
glass that has failed and shattered into sharp pieces.
Caution
Figure 6.1 Lamp Module
To reduce the risk of cuts to fingers and/or decreasing image quality by touching the lens, do not insert hand
into the empty lamp compartment when the lamp has been removed.
Caution
EPS-124A
1
2
1
3
4
4
5
2
6.3 Replacing the Lamp
WARNING
To reduce the risk of electrical shock, always turn off projector and disconnect power cord before changing
lamp.
Downloaded From projector-manual.com 3M Manuals
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m MP8780 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m MP8780 in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of 3m MP8780

3m MP8780 User Manual - German - 22 pages

3m MP8780 User Manual - Dutch - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info