654494
22
Zoom out
Zoom in
Previous page
1/26
Next page
3M 1999 3M Multimedia Projector MP8750 17
Section 7: Troubleshooting
7-1. Troubleshooting Problems and Solutions
Problem Probable Cause Possible Solution
Image is disturbed
or unstable.
Wrong Sync setting.
Wrong Tracking
value.
Set to factory default setting. (See below!)
Change Sync setting in the Picture menu for optimum
performance
For vertical interference stripes, change the Tracking in the
Picture menu for optimum performance.
No computer image
projected. Message
Looking for signal
... displays.
Loose cable.
No power to
computer.
Wrong synchro-
nization mode.
Check and secure cable connections.
Turn on computer.
Adjust synchronization mode of the projector to the synchro-
nization mode of the computer via Advanced Setup menu.
No video image
projected.
Loose cable.
No signal from video
source.
Check and secure cable connections.
Check video picture on TV.
Mouse does not
work.
Loose cable.
Wrong connection.
Wrong power up
sequence.
Check and secure cable connections.
For PS/2 and ADB (Apple) mouse a special adapter is
necessary. Only use adapters from the original manufacturer
(Section 8-2).
The mouse emulation operates correctly only if the correct
power up sequence has been used (refer to section 3-5.)
Image off-center.
Image position. Center image with the Disc Pad of the control panel or on
the remote control transmitter.
Cannot get entire
image on the
screen.
Wrong Tracking
value.
Compatibility
problem.
If vertical interference stripes occur, change the Tracking
value in the Picture menu for optimum performance.
Refer to the documentation for your graphic card. Change
the Resolution setting in the Picture menu to the resolution
of the video mode output from the computer graphic card.
Washed out image.
Wrong Contrast
setting.
Wrong Brightness
setting.
Change Contrast setting in the Picture menu. The bar
should be in the middle position.
Lower Brightness setting in the Picture menu. Choosing
Brightness and pressing Enter can perform an automatic
adjustment.
Humming noise.
Slowly passing
horizontal bars.
Signal sources are
connected to different
power sources.
VCR connected to
aerial system and to
projector.
Bad signal.
Locate the source of disturbance. Disconnect the sources
one after another from the projector. Connect all sources to
a common power source.
Remove antenna connection from VCR. If the disturbance
disappears, use a by-pass filter (isolating transformer) to
connect the antenna to the VCR.
Try different input source.
The factory default settings of the projector can be restored by pressing Enter and Mute simultaneously on the control panel
when switching on the main power switch of the projector and pressing the Standby button afterwards.
The projector will start immediately and the message Parameter factory settings restoreddisplayed in the starting
screen will indicate the default settings are reset.
7-2. Service Information
For product information, product assistance, service information, or to order accessories or spare parts, please call:
In U.S. or Canada: 1-800-328-1371
In other locations, contact your local 3M Sales office.
Downloaded From projector-manual.com 3M Manuals
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3m MP8750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3m MP8750 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of 3m MP8750

3m MP8750 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info