534678

3Dprintingsystems UP Plus Manual

21
Zoom out
Zoom in
Previous page
1/56
Next page
UP Plus
3D Printer User Manual
Now click “To
Bottom” in the Maintenance screen.
NOTE 1:
If you find you cannot get the platform any higher,
copy the value from
“Max: xx”
diagram and click “To:”.
Now to increase the Max height, click “Set Nozzle Height”
and click “Yes” to save it.
You will notice that the Max value has increased by 1mm.
Repeat the above
“Note 1” until the platform is 0.2mm
away from the nozzle.
TIP a:
Once you have setup the nozzle height once, you
now saved in the printer.
TIP b:
You may need to regularly recalibrate nozzle height after moving the printer, or if you find
the models are not adhering to the platform properly, or are warping.
TIP c:
If you happen to crash the platform into the nozzle while
always re-initialis
e the printer before undertaking any
not need to intialise the printer after every print.
a print.
3.1.7
Loading the filament into the Extru
Click on the menu “3DPrint”
to heat. (
Takes approximately 10mins)
After the printer nozzle has warmed up to 260°C, the printer will beep. Push the filament into the
hole at the top
of the extruder head and
extruder motor grabs it and starts pulling it through the extrusion head. The extruder will then a
tomatically extrude a thin filament of material.
extrusion process is complete), pull away the piece of extruded plastic.
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
Bottom” in the Maintenance screen.
If you find you cannot get the platform any higher,
then:
“Max: xx”
into the “To:” box as per
Now to increase the Max height, click “Set Nozzle Height”
You will notice that the Max value has increased by 1mm.
“Note 1” until the platform is 0.2mm
Once you have setup the nozzle height once, you
should
do not need to do it again as it is
You may need to regularly recalibrate nozzle height after moving the printer, or if you find
the models are not adhering to the platform properly, or are warping.
If you happen to crash the platform into the nozzle while
setting the
height adjustm
e the printer before undertaking any
further operations and start again.
not need to intialise the printer after every print.
Only
when switching on the printer
Loading the filament into the Extru
der Head
Click on the menu “3DPrint”
-> “Maintenance” -> “Extrude
”. The printer extruder will now start
Takes approximately 10mins)
After the printer nozzle has warmed up to 260°C, the printer will beep. Push the filament into the
of the extruder head and
push the filament in
with some gentle pressure until the
extruder motor grabs it and starts pulling it through the extrusion head. The extruder will then a
tomatically extrude a thin filament of material.
After the printer beeps a
second time (meaning the
extrusion process is complete), pull away the piece of extruded plastic.
Troubleshooting
do not need to do it again as it is
You may need to regularly recalibrate nozzle height after moving the printer, or if you find
height adjustm
ent,
further operations and start again.
You do
when switching on the printer
or cancelling
der Head
”. The printer extruder will now start
After the printer nozzle has warmed up to 260°C, the printer will beep. Push the filament into the
with some gentle pressure until the
extruder motor grabs it and starts pulling it through the extrusion head. The extruder will then a
u-
second time (meaning the
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for 3Dprintingsystems UP Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of 3Dprintingsystems UP Plus in the language / languages: English as an attachment in your email.

The manual is 7,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info