796991

ZyXEL Nebula LTE7461-M602 Manual

186
Zoom out
Zoom in
Previous page
1/361
Next page
Chapter 10 Routing
Nebula Mobile Router User’s Guide
186
Figure 117 Network Setting > Routing > Static Route > Add New Static Route
The following table describes the labels in this screen.
10.2.1.1 An Example of Adding a Static Route
In order to extend your Intranet and control traffic flowing directions, you may connect a router to the
Zyxel Device’s LAN. The router may be used to separate two department networks. This tutorial shows
how to configure a static routing rule for two network routings.
In the following figure, router R is connected to the Zyxel Device’s LAN. R connects to two networks, N1
(192.168.1.x/24) and N2 (192.168.10.x/24). If you want to send traffic from computer A (in N1 network) to
computer B (in N2 network), the traffic is sent to the Zyxel Device’s WAN default gateway by default. In
this case, B will never receive the traffic.
Table 64 Network Setting > Routing > Static Route > Add New Static Route
LABEL DESCRIPTION
Active Click to enable ( ) and to activate static route. Otherwise, click to disable.
Route Name Assign a name for your static route (up to 15 characters). Special characters are allowed
except the following: double quote (") back quote (`) apostrophe or single quote (') less than
(<) greater than (>) caret or circumflex accent (^) dollar sign ($) vertical bar (|) ampersand (&)
semicolon (;)
IP Type Select between IPv4 or IPv6. Compared to IPv4, IPv6 (Internet Protocol version 6), is designed to
enhance IP address size and features. The increase in IPv6 address size to 128 bits (from the 32-
bit IPv4 address) allows up to 3.4 x 1038 IP addresses. The Zyxel Device can use IPv4/IPv6 dual
stack to connect to IPv4 and IPv6 networks, and supports IPv6 rapid deployment (6RD).
Destination IP
Address
This parameter specifies the IP network address of the final destination. Routing is always based
on network number. If you need to specify a route to a single host, use a subnet mask of
255.255.255.255 in the subnet mask field to force the network number to be identical to the host
ID.
Subnet Mask If you are using IPv4 and need to specify a route to a single host, use a subnet mask of
255.255.255.255 in the subnet mask field to force the network number to be identical to the host
ID. Enter the IP subnet mask here.
Use Gateway IP
Address
The gateway is a router or switch on the same network segment as the device's LAN or WAN
port. The gateway helps forward packets to their destinations.
Click this switch to enable or disable the gateway IP address. When the switch goes to the right,
the function is enabled. Otherwise, it is not.
OK Click this to save your changes.
Cancel Click this to exit this screen without saving.
… 186 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZyXEL Nebula LTE7461-M602 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZyXEL Nebula LTE7461-M602 in the language / languages: English as an attachment in your email.

The manual is 10.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info