679708

ZyXEL IES-1000 Manual

79
Zoom out
Zoom in
Previous page
1/313
Next page
IES-1000 User’s Guide
Getting Started Screens 10-5
Table 10-3 Bridge Packet Type Filter Setup
LABEL DESCRIPTION
Packet Filter Type Choose Any or IP or PPPoE from the drop-down list. Choose Any to allow all kinds of
packets, IP to allow IP packets only or PPPoE to allow PPPoE packets only.
Apply Click Apply to save your changes back to the IES-1000's volatile memory. The IES-1000
loses these changes if it is turned off or loses power, so use the Config Save link on the
navigation panel to the left to save your changes to the non-volatile memory when you
are done configuring.
Reset Click Reset to begin configuring this screen afresh.
10.5 Port Filter (Port-based VLAN)
The IES-1000 port filter (or port-based VLAN) mechanism can be used to limit the broadcast domain to the
members of a port filter group only. In this way, the port filter increases network performance by limiting
broadcasts to a smaller and more manageable logical broadcast domain. In traditional switched environments, all
broadcast frames go to each and every individual port.
The stations on a logical network belong to one group; however, a station can belong to more than one group.
Subscribers of one group are not allowed to access the resources of other groups and a higher level of security is
achieved. This isolates the subscribers from one another and prevents a subscriber from discovering the resources,
for example, shared drives or printers, of another subscriber.
In the IES-1000 port filter, the allowable outgoing port(s) of each incoming port must be defined. Ethernet frames
are forwarded according to these rules. Therefore, if you wish to allow two subscriber ports to talk to each other,
for example, between conference rooms in a hotel, you must define the egress port (outgoing port) for both ports.
An egress port is an outgoing port, that is, a port through which a data frame leaves. Port filters are specific only to
the switch on which they were created.
The factory default settings for the port-based filter of the IES-1000 are:
- Bridge port 1 (Ethernet port) allowed to all bridge ports
- Bridge port 2 (DSL port 1) allowed to bridge port 1 (Ethernet port) only
- Bridge port 3 (DSL port 2) allowed to bridge port 1 (Ethernet port) only
- Bridge port 4 (DSL port 3) allowed to bridge port 1 (Ethernet port) only
- Bridge port 5 (DSL port 4) allowed to bridge port 1 (Ethernet port) only
- Bridge port 6 (DSL port 5) allowed to bridge port 1 (Ethernet port) only
- Bridge port 7 (DSL port 6) allowed to bridge port 1 (Ethernet port) only
- Bridge port 8 (DSL port 7) allowed to bridge port 1 (Ethernet port) only
- Bridge port 9 (DSL port 8) allowed to bridge port 1 (Ethernet port) only
The default port filter settings allow each DSL port to communicate back and forth with only the Ethernet port,
and not with other DSL ports. The following figure illustrates this.
… 79 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ZyXEL IES-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ZyXEL IES-1000 in the language / languages: English as an attachment in your email.

The manual is 5,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info