666218

Zoom Studio 1204 Manual

32
Zoom out
Zoom in
Previous page
1/38
Next page
Troubleshooting
If there seems to be a problem with your 1204, please check the
following points first.
■ 31 ■
Symptom
Check Remedy
No sound or volume is very
low.
Is AC adapter connected correctly and is unit turned
on?
Make connections as described in "Connections"
and turn the unit on as described in "Power-on. "
Is instrument connected correctly to INPUT jack and
playback system to OUTPUT jack?
Make connections as described in "Connections. "
Is shielded cable defective? Try replacing the cable.
Are connected instrument and playback system
functioning correctly? Are all volume controls set to
proper levels?
Check all devices and adjust controls.
Are INPUT and OUTPUT level controls of 1204 set
to proper levels?
Adjust controls for proper matching with connected
equipment.
Are effects set to off and is MIX LEVEL control
turned towards WET?
Adjust MIX LEVEL control.
Are EQ LOW and EQ HIGH controls turned all the
way down?
Adjust EQ controls.
Is a microphone connected to the rear-panel input?
Does microphone impedance match the requirements
of 1204?
Use the front-panel MIC IN jack for a microphone
and use a dynamic microphone rated for 600-ohm
impedance.
Sound is distorted or
breaks up.
Is input signal level too high? Adjust INPUT level control so that PEAK indicator
lights up only occasionally during signal peaks.
Is EQ LOW or EQ HIGH control turned all the way
up?
Adjust EQ controls.
Sound is different from
setting of front-panel
controls.
Is memory mode selected? Use MODE key to switch to manual mode.
Is recall mode activated? Press CANCEL key to terminate recall mode and use
MODE key to switch to manual mode.
Are effects switched off? Press EFFECT key to turn effects on.
Stored settings are different
from established settings.
Settings were made in manual mode but unit was
switched to memory mode before storing?
When mode is switched, settings are lost. Make the
settings again and repeat the store process without
switching modes.
Settings were made in memory mode but unit was
switched to manual mode before storing?
When mode is switched, settings are lost. Make the
settings again and repeat the store process without
switching modes.
Settings were made in memory mode but memory
number was changed before activating store standby
condition?
When memory number is changed, settings are lost.
Make the settings again and activate store standby
before changing memory numbers.
Symptom
Check Remedy
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom Studio 1204 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom Studio 1204 in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info