666218
23
Zoom out
Zoom in
Previous page
1/38
Next page
Using MIDI to change effect parameters
The 1204 allows the use of MIDI control change messages to change effect parameters. This includes all
parameters except changing the effect type (as performed with the EFFECT selector or BANK switch) and
adjusting the INPUT and OUTPUT level controls. Using control change messages to change effect parameters is
called real-time modulation and differs from the parameter editing process described in the previous section. When
real-time modulation is used, the effect sound as heard in the output changes, but the actual effect settings are not
altered. Consequently, if memory store is carried out in this condition, the same settings as before will be stored.
To change effect parameters via MIDI, proceed as follows.
1. Connect the MIDI OUT jack of the external device to the MIDI IN jack of the 1204.
Turn all devices off before making this connection.
2. When connections are established, turn on the devices and use the MODE key of the 1204 to set it to the
memory mode.
3. Set up the 1204 so that the MIDI receive channels match the MIDI send channels of the external device.
4. Send control change messages from the external device to change effect parameters at the 1204.
Note: The relationship between MIDI control change messages and effect parameters of the 1204 is as
shown below.
Recalling Factory Default Memory Settings
The 1204 is shipped from the factory with 100 recommended effect settings already stored in memory. When the
user stores settings in memory, these factory defaults are overwritten, but they can be restored using the recall
function. The recall mode is a special mode of the 1204 that is separate from the other two operation modes. It
cannot be activated when the unit is already turned on. The unit must be turned off and then turned on by a special
procedure, as described below.
In recall mode, all 100 settings can be restored together, and it is also possible to restore individual settings.
To use the recall mode, proceed as follows.
1. Turn the unit off.
2. Keep the STORE key depressed while turning the unit on with the POWER switch.
3. The indication
AL
"AL" flashes on the display.
4. When wishing to restore all 100 settings together, press the STORE key once more in this condition.
The indication on the display flashes more rapidly. When the recall process is completed, the unit
automatically switches to the memory mode.
5. When wishing to restore only a particular memory number, use the and keys to select the desired
number in step 3.
6. When the desired memory number is displayed, press the STORE key. The indication on the display
flashes more rapidly and the contents of that memory number are returned to the factory default.
7. Because the unit does not automatically switch to the memory mode when individual memory numbers
are being restored, it is possible to restore several numbers in succession. When you wish to terminate the
recall mode, press the CANCEL key. The 1204 then switches to the memory mode. Turning the unit off
also terminates the recall mode.
22
Effect parameter
MIDI control change number
PATTERN select 84
EDIT1 control
85
EDIT2 control
86
EQ LOW control
87
EQ HIGH control 88
MIX LEVEL control 8
EFFECT ON, OFF 80, 91
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom Studio 1204 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom Studio 1204 in the language / languages: English as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info