533782

Zoom MRS-802 Manual

36
Zoom out
Zoom in
Previous page
1/184
Next page
Reference [Recorder]
ZOOM MRS-802
36
key to begin recorder playback.
5.
When you come to the punch-in point, press the
REC [
O
] key (or press the foot switch).
The REC [O] key lights up, and track recording begins from
that location.
6.
When you come to the intended punch-out point,
press the REC [
O
] key (or the foot switch) once
again.
The REC [O] key goes out, and the unit switches from
recording to playback.
7.
To stop playback, press the STOP [
P
] key.
8.
To check the newly recorded content, locate to a
point slightly before the punch-in point, and press
the PLAY [
R
] key.
Using auto punch-in/out
Auto punch-in/out is a function that lets you specify
beforehand the region to be re-recorded. Punch-in will occur
automatically when you reach the starting location (In
point), and punch-out will occur automatically when you
reach the ending location (Out point). This is convenient for
example when you cannot operate the MRS-802 because
you are playing the instrument yourself, or when very fast
playback/record switching is required.
In order to perform auto punch-in/out, you must first specify
the In point (switch point from playback to recording) and
Out point (switch point from recording to playback), and
then perform the recording operation. The procedure is as
follows.
1.
Raise the fader of the track where you want to
perform auto punch-in/out to a suitable position.
2.
While playing the instrument connected to the
input jack, use the [INPUT] control and [REC
LEVEL] control to adjust the recording level.
3.
Locate the point at which you want to punch-in,
and press the [AUTO PUNCH-IN/OUT] key.
The [AUTO PUNCH-IN/OUT] key flashes. This sets the “In
point” at which recording will begin.
4.
Locate the point at which you want to punch-out,
and press the [AUTO PUNCH-IN/OUT] button once
more.
This sets the “Out point” at which recording will end. The
[AUTO PUNCH-IN/OUT] button will change from flashing
to solidly lit. This indicates that the auto punch-in/out
function is now enabled.
HINT
If you want to specify the in/out points precisely, it is
convenient to use the scrub function (
→ p. 44) to find the
locations and assign a mark (
→ p. 42) beforehand at the
desired locations.
5.
Use the Locate function to go to a spot slightly
before the In point.
6.
Repeatedly press the status key for the track on
which you want to perform punch-in/out, until the
key flashes red.
NOTE
A status key that is lit red means that the current location is
between the In point and Out point. In this case, operate the
transport once again to locate to a point that is earlier than
the In point.
7.
If you want to rehearse the auto punch-in/out,
press the PLAY [
R
]key.
The recorder will begin playing. When you reach the In
point, the track on which you are punching-in/out will be
muted. When you reach the Out point, muting will be
defeated. (You will always be able to monitor the input
signal during this time.) Performing this action will not
delete or record anything on the track.
When you are finished rehearsing, move again to a location
earlier than the In point. If necessary, adjust the In/Out
points.
8.
To actually perform auto punch-in/out, hold down
the REC [
O
] key and press the PLAY [
R
] key.
The recorder operates in playback mode. When you reach
In point
Track
Playback Playback Recording
Out point
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom MRS-802 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom MRS-802 in the language / languages: English as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zoom MRS-802

Zoom MRS-802 User Manual - German - 180 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info