629759
24
Zoom out
Zoom in
Previous page
1/37
Next page
Restoring Factory Defaults
ZOOM B2.1u
24
To use this function, connect the [BALANCED
OUT] connector of the B2.1u to the PA mixer or
recording console, using XLR balanced cable. At
the same time, you can also connect the
[OUTPUT/PHONES] jack to the bass amplifier
for monitoring. (The amp settings will have no
effect on the signal supplied at the [BALANCED
OUT] connector.)
The [PRE/POST] switch lets you control the type
of signal supplied at the [BALANCED OUT]
connector. To use the signal after effect
processing, select the "POST" position (switch
engaged). To use the signal before effect
processing, select the "PRE" position (switch
disengaged).
In certain configurations, a ground loop (electrical
signal loop created because devices within the
same system are connected to a separate ground)
may occur, leading to noise problems (audible
hum). In such a case, try setting the [GROUND]
switch to "LIFT". This may help to eliminate or
reduce the noise.
HINT
The [GROUND] switch determines whether the
[BALANCED OUT] connector is grounded or not.
When the switch is set to the "LIFT" position (switch
engaged), the ground pin of the [BALANCED OUT]
connector is uncoupled from the signal path. This can
be effective in eliminating or reducing hum noise
caused by a ground loop.
Mixer
Bass amp
Bass guitar
B2.1u
[BALANCED OUT]
connector
[OUTPUT/PHONES]
jack
Restoring Factory Defaults
In the factory default condition, the patches of the user area (A0 – d9) contain the same settings as the
patches of the preset area (00 – 39). Even after overwriting the user patches, their original content can be
restored in a single operation ("All Initialize" function).
1. Turn the B2.1u on while holding down
the [STORE] key.
The indication "AL" appears on the display.
2. To carry out the All Initialize function,
press the [STORE] key once more.
All patch settings are returned to the factory
default condition, and the unit switches to play
mode. To cancel All Initialize, press the
RHYTHM [
R/P] key instead of the [STORE]
key.
NOTE
When you carry out All Initialize, any newly created
patches that were stored in the user area will be
deleted (overwritten). Perform this operation with care
to prevent losing any patches that you want to keep.
A L
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoom B2.1u at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoom B2.1u in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info