773322

Zoofari ZTSD 36 B1 - IAN 315533 Manual

17
Zoom out
Zoom in
Previous page
1/60
Next page
■ 14 │ GB│IE ZTSD 36 B1
Operation
The fur to be cut must be dry and clean. Brush the
fur through to remove any knots.
1) Remove the blade guard 7 from the cutting
head 1.
2) Place the required trimming guide (1 – 6) with
the prongs facing upwards on the cutting head 1
and thereby press the flap of the trimming guide
(1 – 6) down firmly onto the lower metal edge
of the cutting head 1 (see illustration).
■ Ensure that the trimming guide (1 – 6) has
properly engaged and is secured before starting
to cut/trim the fur.
NOTE
► It is advisable to first trim a small area so as to
test the individual comb attachments (1 – 6).
Start with a comb attachment for long hair
(1/2“ 4 or 3/8“ 3) and, if necessary, use a
shorter one. The comb attachments (1 – 6)
permit cutting lengths from 3 to 13 mm.
3) Switch the appliance on by sliding the On/Off
switch 3 to the position “ON“.
4) Slowly run the appliance through the fur against
the direction of hair growth. Hold the appliance
so that the trimming guide (1 – 6) is as flat as
possible against the animal.
– In addition, with the adjustment switch 4 the
cutting length of the cutter head 1 can be
adjusted in steps(up to 2 mm) without having
to exchange the comb attachment (1 – 6).
To do this, slide the adjustment switch 4
backwards to increase the cutting length in
steps. With this the cutting length of the
respectively attached comb attachment is also
increased by up to 2mm.
Slide the adjustment switch 4 forward again
to reduce the cutting length or to bring the
comb attachment (1 – 6) back into its
original position.
– Through removal of the individual trimming
guide (1 – 6), i.e. using only the cutting
head 1 itself, you can cut clean contours.
5) After use, switch the appliance off by sliding the
On/Off switch 3 to the position “OFF“.
Cleaning and Care
DANGER! ELECTRIC SHOCK
► Before cleaning, remove the plug from the
mains power socket.
CAUTION! PROPERTY DAMAGE!
► NEVER submerse the appliance in water or
other liquids.
■ Take the respective trimming guide (1 – 6), if
fitted, off.
■ Using exclusively the cleaning brush 8, remove
the hairs from the cutting head 1. Wipe off the
cutting head 1 with a damp cloth. After this,
dry the cutting head 1 off with a dry cloth.
We recommend that you occasionally clean the
cutting head 1 with medicinal alcohol.
■ If in regular use, the cutting head 1 should be
oiled occasionally. For this, use the supplied
blade oil 9.
■ Remove excess oil with a dry cloth.
■ Clean the housing with a soft, dry lint-free cloth.
In cases of stubborn soiling, clean the housing
using a damp cloth and then dry it off with a dry
cloth.
■ Clean the trimming guides (1 – 6) in warm
water. Add a little mild detergent. Dry all parts
well before re-use.
■ Store the appliance in a dry and dust free
location. When it is in storage, place the blade
guard 7 on the cutting head 1.
IB_315533_ZTSD36B1_LB8.indb 14 22.01.19 12:33
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoofari ZTSD 36 B1 - IAN 315533 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoofari ZTSD 36 B1 - IAN 315533 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2.88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info