663407

Zoofari ZTSD 36 A1 - IAN 63602 Manual

14
Zoom out
Zoom in
Previous page
1/16
Next page
- 11 -
Operation
The fur to be cut must be dry and clean. Brush the
fur through to remove any knots.
•
Remove the blade guard from the cutting
head 1
.
• Place the required trimming guide (- )
with the prongs facing upwards on the cutting
head 1 and thereby press the fl ap of the trim-
ming guide down fi rmly onto the lower metal
edge of the cutting head (see illustration).
• Ensure that the trimming guide has properly
engaged and is secured before starting to cut/
trim the fur.
Note:
It is advisable to fi rst trim a small area so as to test
the individual comb attachments. Start with a comb
attachment for long hair (1/2“
or 3/8“
)
and, if necessary, use a shorter one. The comb
attachments permit cutting lengths from 3 to 13 mm.
•
Switch the appliance on by sliding the On/Off
switch 3 to the position „ON“.
• Slowly run the appliance through the fur against
the direction of hair growth. Hold the appliance
so that the trimming guide is as fl at as possible
against the animal.
•
In addition, with the adjustment switch
4
the
cutting length of the cutter head
1
can be
adjusted in steps(up to 2 mm) without having
to exchange the comb attachment. To do this,
slide the adjustment switch
4
backwards to
increase the cutting length in steps. With this the
cutting length of the respectively attached comb
attachment is also increased by up to 2 mm.
Slide the adjustment switch
4
forward again to
reduce the cutting length or to bring the comb
attachment back into its original position.
•
Through removal of the individual trimming
guide, i.e. using only the cutting head
1
itself,
you can cut clean contours.
•
After use, switch the appliance off by sliding the
On/Off switch
3
to the position „OFF“.
Cleaning and Care
Risk of electric shock!
Before cleaning, remove the plug from the mains
power socket.
NEVER submerse the appliance in water or other
liquids.
• Take the respective trimming guide, if fi tted, off .
•
Using exclusively the cleaning brush , remove
the hairs from the cutting head 1
. The cutting
head
1
may not be cleaned with water or
other liquids, except medical alcohol!
•
If in regular use, the cutting head 1
should be
oiled occasionally. For this, use the supplied
blade oil
.
• Remove excess oil with a dry cloth.
• Clean the housing with a soft, dry lint-free cloth.
•
Store the appliance in a dry and dust free
location. When it is in storage, place the blade
guard
on the cutting head
1
.
… 14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zoofari ZTSD 36 A1 - IAN 63602 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zoofari ZTSD 36 A1 - IAN 63602 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info