460200
7
Zoom out
Zoom in
Previous page
1/14
Next page
Check whether the fuel cap is straight and tightened properly. Reinstall the
removable tank in the heater (cap down). Close the lid.
C S E T T I N G T H E C L O C K
It is only possible to set the correct time, when the heater is connected to the
mains and not burning. Use the adjustment keys ƹ to set the time. First press
either of the two keys to switch on the function (the 4-digit ¸ will start blinking).
Next, set the hours using the key on the left (Ĭhour) and the minutes using the
key on the right (įmin.). Press once to increase the value by one step. When you
hold down the key, the value will continue going up, until you release the key
again. After approximately 10 seconds the 4-digit will stop blinking and the
setting
will be locked. 5 minutes after switching off the heater, the information on
the display will disappear and the heater will automatically switch into the stand-
by position.
W
hen the heater has been unplugged (or after a power failure), the time needs
to be set again.
D I G N I T I N G T H E H E A T E R
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation.
Always ignite the heater with the
button ¹
. Never use matches or a cigarette
lighter.
Just press the button ¹ to ignite the heater. The POWER lamp will start
blinking, indicating that the ignition procedure has started. This will take a short
while. Once the heater is burning, the POWER lamp will remain lit (red). The
information display ¸ will show two numbers. The light next to them indicates
that these numbers refer to the temperatures (Fig. F). The actual room temperature
is indicated below ROOM, while the temperature setting is indicated below SET.
The latter can be changed with the adjustment keys
(refer to Section E).
Prior to igniting the heater, always check for sufficient fuel in the removable tank.
E S E T T I N G T H E R E Q U I R E D T E M P E R A T U R E
The temperature setting can only be adjusted, when the heater is burning. Use the
adjustment keys ƹ to adjust the temperature. First press either of the two keys to
switch on the function (the °C mark ¸ will start blinking). Next, adjust the
temperature
using the key on the right (įmin.) to set the temperature to a higher
setting and the key on the left (Ĭhour) to lower the temperature. Press once to
increase the value one step. After approximately 10 seconds the °C mark will stop
blinking and the setting will be locked (Fig. F).
The a
vailable temperature settings range from 6°C minimum to 28°C maximum.
When the heater has been unplugged (or after a power failure), the temperature
will reset to the factory setting of 20°C.
6
4
56
F: The required
temperature on the left,
the measured
temperature on the
right.
E: When the 4-digit stops
blinking, the setting has
been locked to the
indicated value.
  
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zibro SRE229TC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zibro SRE229TC in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zibro SRE229TC

Zibro SRE229TC User Manual - German - 14 pages

Zibro SRE229TC User Manual - Dutch - 10 pages

Zibro SRE229TC User Manual - Danish - 14 pages

Zibro SRE229TC User Manual - French - 14 pages

Zibro SRE229TC User Manual - Italian - 14 pages

Zibro SRE229TC User Manual - Polish - 14 pages

Zibro SRE229TC User Manual - Swedish - 14 pages

Zibro SRE229TC User Manual - Spanish - 14 pages

Zibro SRE229TC User Manual - Norwegian - 14 pages

Zibro SRE229TC User Manual - Finnish - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info