481444
8
Zoom out
Zoom in
Previous page
1/18
Next page
4
79
G: The required
temperature on the
left, the measured
temperature on the right.
+
In case of any
malfunctioning the
information display
will tell you what is the
matter.
D IGNITING THE HEATER
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation.
Always ignite the heater with the button
M
. Never use matches or a cigarette
lighter.
Just press the button M to ignite the heater.
The button will start blinking, indicating that the ignition procedure has started.
This will take a short while. Once the heater is burning, the button M will remain
lit (red). The information display L will show two numbers (Fig. G). The actual
room temperature is indicated below ROOM, while the temperature setting is
indicated below SET. The latter can be changed with the adjustment keys (refer to
Section E).
Prior to igniting the heater, always check for sufficient fuel in the removable tank.
E SETTING THE REQUIRED TEMPERATURE
The temperature setting can only be adjusted, when the heater is burning. Use
the adjustment keys O to adjust the temperature. First press either of the two
keys to switch on the function (the °C mark and 4-digit L will start blinking). Next,
adjust the temperature using the key (Mmin.) to set the temperature to a higher
setting and the key (Nhour) to lower the temperature. Press once to increase the
value one step. After approximately 10 seconds the °C mark and 4-digit will stop
blinking and the setting will be locked (Fig. F).
The available temperature settings range from 6°C minimum to 28°C maximum.
When the heater has been unplugged for more than 10 minutes (or after a power
failure), the temperature will reset to the factory setting of 20°C.
F SWITCHING OFF THE HEATER
There are two ways to switch off the heater.
1
Press the button M. The information display will show the CLOCK
signal. Within approximately one minute the flame will have extinguished.
2
Press the TIMER key P, when you want to switch off the heater and ignite it
again with the timer the next time. This not only switches off the heater, but
it also activates the timer function.
G THE INFORMATION DISPLAY
The information display L not only serves as an indicator of the (set) time and
temperature (Sections C, E, and F), it also indicates any malfunctioning of the
heater. The code on the information display tells you what is the matter:
CODE INFORMATION WHAT TO DO
e - 0 Temperature within the heater too high. Cool-down and re-ignite.
f - 0 Power interrupted. Re-ignite the heater.
e - 1 Faulty thermostat. Contact your dealer.
f - 1 Faulty burner thermistor. Contact your dealer.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zibro SRE 346 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zibro SRE 346 E in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zibro SRE 346 E

Zibro SRE 346 E User Manual - German - 20 pages

Zibro SRE 346 E User Manual - Dutch - 18 pages

Zibro SRE 346 E User Manual - Danish - 18 pages

Zibro SRE 346 E User Manual - French - 21 pages

Zibro SRE 346 E User Manual - Italian - 18 pages

Zibro SRE 346 E User Manual - Polish, Swedish - 18 pages

Zibro SRE 346 E User Manual - Spanish - 18 pages

Zibro SRE 346 E User Manual - Norwegian - 18 pages

Zibro SRE 346 E User Manual - Finnish - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info