Manual Zibro SRE 240E (page 7 of 14) (English)

564047

Zoom out

Zoom in

1/14

Let the remaining fuel in the pump flow back into the jerrycan and carefully

remove the pump. Carefully screw the fuel cap back on the tank. Clean off

any spilled fuel.

Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

C SETTING THE CLOCK

It is only possible to set the correct time, when the heater is connected to the

mains and not burning. Use the adjustment keys

ƺ to set the time. First press

either of the two keys to switch on the function (the 4-digit

¹ will start blinking).

Next, set the hours using the key (

hour) and the minutes using the key ( min.).

Press once to increase the value by one step. When you hold down the key, the

value will continue going up, until you release the key again. After approximately

10 seconds the 4-digit will stop blinking and the setting will be locked. 5 minutes

after switching off the heater, the information on the display will disappear and

the heater will automatically switch into the stand-by position.

When the heater has been unplugged for more than 10 minutes (or after a

power failure), the time needs to be set again.

D IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Always ignite the heater with the button

. Never use matches or a cigarette

lighter.

Just press the button Ƹ to ignite the heater. The button will start

blinking, indicating that the ignition procedure has started. This will take a short

while. Once the heater is burning, the button

Ƹ will remain lit (red). The

information display

¹ will show two numbers (Fig. G). The actual room

temperatur

e is indicated below ROOM, while the temperature setting is indicated

below SET. The latter can be changed with the adjustment keys

(refer to Section E).

Prior to igniting the heater, always check for sufficient fuel in the removable tank.

E SETTING THE REQUIRED TEMPERATURE

The temperatur

e setting can only be adjusted, when the heater is bur

ning. Use the

adjustment keys

ƺ to adjust the temperature. First press either of the two keys to

switch on the function (the °C mark and 4-digit

¹ will start blinking). Next, adjust

the temperatur

e using the key (

min.) to set the temperatur

e to a higher setting

and the key (

hour) to lower the temperature. Press once to increase the value

one step. After approximately 10 seconds the °C mark and 4-digit will stop

blinking and the setting will be locked (Fig. F).

The available temperature settings range from 6°C minimum to 28°C maximum.

When the heater has been unplugged for more than 10 minutes (or after a power

failur

e), the temperatur

e will reset to the factory setting of 20°C.

F USING THE TIMER

The timer allows you to switch on the heater automatically at a preset time.

In order to switch on the timer, the correct time must have been set

(refer to

Section C)

and the heater should be of

f. Follow the pr

ocedur

e below:

G: The required

temperature on the left,

the measur

temperature on the

right.

F: When the 4-digit stops

blinking, the setting has

been locked to the

ndicated value.

☞

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zibro SRE 240E in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zibro SRE 240E

Zibro SRE 240E User Manual - German - 14 pages

Zibro SRE 240E User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zibro SRE 240E Manual

Product: