Manual Zibro LC-SL530 Toyotomi (page 21 of 168) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

650600

Zoom out

Zoom in

1/168

E CLEAN START

Clean start function reduces the odor emitted by the heater at the ignition

significantly. It takes one or two more minutes to ignite than normal mode.

By pressing the clean start key N while the heater is off, the indication

is lit and

change to clean start mode.

Once the key is pressed again, the mode will turn off and return to the normal

ignition mode.

F IGNITING THE HEATER

When used for the first time, a new heater may give out a smell for a short while.

You should therefore provide extra ventilation.

Alays ignite the heater ith the

button 

. Never use matches or a

cigarette lighter.

Just press the button  to ignite the heater. The POWER lamp ill start blinking,

indicating that the ignition procedure has started. This will take a short while.

Once the heater is burning, the POWER lamp ill remain lit (red). The information

display  will show two numbers. The light next to them indicates that these

numbers refer to the temperatures (ig. ). The actual room temperature is

indicated belo ROOM, hile the temperature setting is indicated belo SET. The

latter can be changed with the adjustment keys (refer to Section G).

Prior to igniting the heater, alays check for sufficient fuel in the removable tank.

G SETTING THE REQUIRED TEMPERATURE

The temperature setting can only be adjusted, hen the heater is burning. Use

the adjustment keys  to adjust the temperature. irst press either of the to

keys to switch on the function (the °C mark  will start blinking). Next, adjust the

temperature using the key on the right (min.) to set the temperature to a higher

setting and the key on the left ( hour) to loer the temperature. Press once to

increase the value one step. After approimately 10 seconds the C mark ill stop

blinking and the setting ill be locked (ig. ).

The available temperature settings range from 6C minimum to 28C maimum.

When the heater has been unplugged (or after a power failure), the temperature

will reset to the factory setting of 20°C.

H SWITCHING OFF THE HEATER

There are two ways to switch off the heater.

Press the

button . The information display will show the CLOCK

signal. Within approximately one minute the flame will have extinguished.

Press the TIMER key , when you want to switch off the heater and ignite it

again with the timer the next time. This not only switches off the heater, but

it also activates the timer function.

G: The required tempe-

rature on the left, the

measured temperature

on the right.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zibro LC-SL530 Toyotomi in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zibro LC-SL530 Toyotomi

Zibro LC-SL530 Toyotomi User Manual - Dutch - 19 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zibro LC-SL530 Toyotomi Manual

Product: