728824

Zibro LC 140 Manual

21
Zoom out
Zoom in
Previous page
1/168
Next page
4
9
E CLEAN START
Clean start function reduces the odor emitted by the heater at the ignition
significantly. It takes one or two more minutes to ignite than normal mode.
By pressing the clean start key K while the heater is off, the indication
is lit and
change to clean start mode.
Once the key is pressed again, the mode will turn off and return to the normal
ignition mode.
F IGNITING THE HEATER
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation.
Alays ignite the heater ith the
button
. Never use matches or a
cigarette lighter.
Just press the button to ignite the heater. The POWE lamp ill start blinking,
indicating that the ignition procedure has started. This will take a short while.
Once the heater is burning, the POWE lamp ill remain lit (red). The information
display will show two numbers. The light next to them indicates that these
numbers refer to the temperatures (ig. ). The actual room temperature is
indicated belo OOM, hile the temperature setting is indicated belo SET. The
latter can be changed with the adjustment keys (refer to Section G).
Prior to igniting the heater, alays check for sufficient fuel in the removable tank.
G SETTING THE REQUIRED TEMPERATURE
The temperature setting can only be adjusted, hen the heater is burning. Use
the adjustment keys to adjust the temperature. irst press either of the to
keys to switch on the function (the °C mark will start blinking). Next, adjust the
temperature using the key on the right (min.) to set the temperature to a higher
setting and the key on the left (hour) to loer the temperature. Press once to
increase the value one step. After approimately 10 seconds the C mark ill stop
blinking and the setting ill be locked (ig. ).
The available temperature settings range from C minimum to 28C maimum.
When the heater has been unplugged (or after a power failure), the temperature
will reset to the factory setting of 20°C.
H SWITCHING OFF THE HEATER
There are two ways to switch off the heater.
1
Press the
button . The information display will show the CLOCK
signal. Within approximately one minute the flame will have extinguished.
2
Press the TIME key , when you want to switch off the heater and ignite it
again with the timer the next time. This not only switches off the heater, but
it also activates the timer function.
G: The required tempe-
rature on the left, the
measured temperature
on the right.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zibro LC 140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zibro LC 140 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info