481445
38
Zoom out
Zoom in
Previous page
1/71
Next page
Chapter 1, INSTALLATION
39
CHECKLIST
Check whether the heater has been connected to a
suitable socket.
Check that a suitable quantity of petroleum is in the
fuel tank.
Ensure that the fuel is free of water or other
contaminants.
Check that the fuel tank is in good working order –
it must be free of rust, corrosion and/or leaks.
Inspect the fuel pipe for signs of leaks, loose
connections, cracks, air bubbles or blockages.
Check that the fuel valves on the fuel tank and the
fire safety valve are open in order to allow the free
flow of fuel.
Check outside the building in order to ascertain that
there is no fuel or obstructions to the free
circulation of air in the area immediately adjacent
to the exhaust pipe.
Inspect the inlet air hose for cracks, loose
connections or blockages.
Check the outlet air hose for cracks, loose
connections or blockages.
Check the back of the heater to ensure that the
airflow to the air circulation ventilator is not
obstructed.
Inspect the interior of the building to ensure that
the area immediately adjacent to the heater is free
of fuel and objects that may obstruct the free flow
of air.
Check that the room sensor is not exposed to
draughts, direct sunlight or heat radiated directly
from the heater.
Use a spirit level to check that the heater is level.
If this inspection brings any faults to light, resolve these
problems before using the heater.
Use only water-free high quality pure
paraffin oil. Never use gasoline, LPG,
camping gas or other flammable liquids.
The use of these substances may cause
explosions or fire.
Available fuel supply options
The fuel supply of the Laser 95 can be set up as follows:
Large gravity-operated exterior tank
To install a large gravity-operated exterior tank, follow
the instructions below. We recommend that you call in
a recognised installer.
The inlet pressure to the heater may not exceed 2.5 psi.
Use a pressure reduction valve with a maximum thrust
of 2.5 psi ( ± 0.17 bar).
The installation height of the bottom of the fuel tank
must be 40 cm or more above the level of the floor on
which the heater is standing. This will ensure that there
is sufficient fuel inlet pressure. The distance between
the floor surface on which the heater is standing and
the top of the fuel tank may not exceed 2.5 metres.
This will prevent excessive fuel inlet pressures.
The pipe may not have any inverted U-bends (to pre-
vent air pockets that may block the fuel supply).
We recommend using a water-blocking filter in the fuel
pipe leading into the tank. A cut-off valve must be fit-
ted to the tank.
We recommend installing a fire safety valve and a fuel
filter in the fuel pipe.
The use of a cut-off valve, placed just before the pipe
enters the building, will limit the quantity of fuel to be
tapped off to a minimum if the heater requires mainte-
nance.
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zibro Laser FF 95 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zibro Laser FF 95 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zibro Laser FF 95

Zibro Laser FF 95 User Manual - Dutch - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info