781876
13
Zoom out
Zoom in
Previous page
1/16
Next page
13GB
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
Tool removal (Fig. 4)
Pull back and hold the locking sleeve (2) and remove
the tool.
Dust collection device (Fig. 5)
Slide the dust collection device (a) over the drill bit be-
fore carrying out any hammer drilling vertically above
your head.
Starting up
Important.
To prevent all danger, the machine must only be
held using the two handles. Otherwise there may
be a risk of suffering an electric shock if you drill
into cables.
Switching on and off (Fig. 1)
To switch on: Press the control switch (4).
To switch off: Release the control switch (4).
Setting the operating mode (Fig.6)
The operating mode of the power tool is selected with
the mode selector switch
Note: Change the operating mode only when the
machine is switched off! Otherwise, the machine can
be damaged.
– Turn the mode selector switch to the requested
position.
Position for hammer drilling (A): When the drilling
tool does not immediately rotate upon switching on,
allow the machine to run slowly until the drilling tool
rotates.
Vario-Lock (B) position for adjustment of the
chiselling position
Position for chiselling (C)
Important.
Only low pressure is required for hammer drill-
ing. Excessive pressure will exert an unnecessary
force on the motor. Check the drill bits at regular
intervals. Sharpen or replace blunt drill bits.
Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its aftersales
service or similarly trained personnel to avoid danger.
Cleaning and maintenance
Always pull out the mains power plug before starting
any cleaning work.
Cleaning
Keep all safety devices, air vents and the motor hous-
ing free of dirt and dust as far as possible. Wipe the
equipment with a clean cloth or blow it with com-
pressed air at low pressure.
We recommend that you clean the device immediately
each time you have nished using it.
Clean the equipment regularly with a moist cloth and
some soft soap. Do not use cleaning agents or sol-
vents; these could attack the plastic parts of the equip-
ment. Ensure that no water can seep into the device.
Carbon brushes
In case of excessive sparking, have the carbon brushes
checked only by a qualied electrician. Important! The
carbon brushes should not be replaced by anyone but
a qualied electrician.
Maintenance
There are no parts inside the equipment which require
additional maintenance.
Disposal and recycling
The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material and
can therefore be reused or can be returned to the raw
material system.
The unit and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask your
dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must not
be disposed of together with domestic waste in
compliance with the Directive (2012/19/EU) per-
taining to waste electrical and electronic equip-
ment (WEEE). This product must be disposed of at a
designated collection point. This can occur, for exam-
ple, by handing it in at an authorised collecting point for
the recycling of waste electrical and electronic equip-
ment. Improper handling of waste equipment may have
negative consequences for the environment and human
health due to potentially hazardous substances that are
often contained in electrical and electronic equipment.
By properly disposing of this product, you
are also contributing to the effective use of natural re-
sources. You can obtain information on collection points
for waste equipment from your municipal administration,
public waste disposal authority, an authorised body for
the disposal of waste electrical and electronic equip-
ment or your waste disposal company.
Spare-part ordering
Please quote the following in your order for spare parts:
Type of device
Article No. of deviceIdent. No. of device
Spare Part No. of the required spare part
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consumab-
les.
Wear parts*: Carbon brushes.
* Not necessarily included in the scope of delivery!
Storage
Store the equipment and accessories out of children’s
reach in a dark and dry place at above freezing tempera-
ture. The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original packaging.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zgonc YPL 1500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zgonc YPL 1500 in the language / languages: English, German as an attachment in your email.

The manual is 1.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info