623342

Zennio Z41 Pro Touch Panel Manual

57
Zoom out
Zoom in
Previous page
1/96
Next page
Z41 Pro
http://www.zennio.com Tecnical Support: http://support.zennio.com
57
1. The first touch on the increase button will trigger the sending of the value
“0.5”, so that the thermostat sets the setpoint to 25.5ºC. This value will be
then sent through the status object, and afterwards shown by Z41 Pro in
the corresponding box.
2. A second touch will trigger the value “1”, after which the setpoint will
become 26ºC.
3. On the third touch, the value sent will be “1.5”, so the setpoint will be set to
26.5ºC.
And so on until the offset sent becomes 10 (setpoint of 35ºC). Any further
presses on the increase button will send the value “10” again, so the setpoint
will remain at 35ºC, while touching the decrease button for the first time will
trigger the sending of the value “9.5”, setting the temperature back to 34.5ºC.
On the second button press, the value “9” will be sent, and the setpoint will
become 34ºC. And so on until an offset of “-10” (setpoint of 15ºC) is reached.
From that moment, any further presses on the decrease button will re-send the
value “-10” and the setpoint will remain at 15ºC.
Important: the control object for the floating point relative setpoint control
has its Write flag enabled with the intention of permitting the reception of
feedback from the thermostat, which may reset or modify the status of the
offset for any reason at any time. This feedback allows that Z41 Pro
updates its own value to equal that from the external thermostat. Thinking
of the above example, if Z41 Pro receives the value “0” after having the
user performed three presses on the increase button (therefore, after
having been sent the value “1.5” to the bus), it will happen that on the forth
press the value sent will be “0.5” and not “2”.
Figure 56 Relative (Float) Setpoint Control. Object Linking.
Z41
Pro
Thermostat
Control object
Status object
Offset
Offset (status)
Setpoint T. (status)
… 57 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zennio Z41 Pro Touch Panel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zennio Z41 Pro Touch Panel in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info