464204
25
Zoom out
Zoom in
Previous page
1/36
Next page
ZE-MC294
25
DEVICE CONNECTIONS
NOTES OF CONNECTION
This unit is designed to be used in a vehicle with a 12-volt battery and negative
grounding. Before installing this unit to a mobile home, a bus, or a truck, make sure the
battery voltage is appropriate for this unit to be used, otherwise, install a transformer to
convert the output voltage to 12 V DC.
To avoid short circuits in the electrical system, ensure that the negative battery cable is
disconnected before installation.
To prevent short circuiting in the wiring which could lead to damage of this unit, secure
all wirings with cable ties and/or adhesive tape. Route the wirings in a secure manner,
stay away from hot or moving parts such as exhaust pipes, gear shift, handbrake, and
seat rails to prevent the wiring insulation being melted/wore off.
Never pass the yellow power cord through the installation hole into the engine
compartment and never ever connect it directly to the car battery. If that happens, it will
most likely produce some serious short-circuits which may permanently damage vital
parts of the electrical system.
Replacing a new fuse with 10 A rating when the old one is broken, using no fuse or
fuse with improper rating may cause damage to this unit or even  re. lf a proper fuse is
installed and electrical problems still occur, please contact your local ZENEC dealer.
DO NOT connect other equipment to the car battery to avoid battery overheating.
Please make sure all the wiring connections and the cables of the speakers are well-
insulated. Otherwise, this unit may be damaged by short circuits.
lf there is no ACC available, please connect ACC lead to the power supply with a switch.
lf an external power ampli er is connected, please don't connect P.CONT lead to the
power lead of the external power ampli er, otherwise, electric sparks or some other
damage may be the result.
Never ground the speaker outputs to prevent damage to the built-in power ampli er.
The minimum rating of the speakers connected to this unit is 40 W with 4 to 8
impedance.
OPTION: CONNECTION TO THE ORIGINALLY EQUIPPED STEERING WHEEL REMOTE
CAN is the abbreviation for Controller Area Network. It is an vehicle speci c Standard-Bus-
Protocol of the car industry. Due to that protocol, the functions of the steering wheel built-
in remote, as well as other vehicle functions, can be accessed and used. Simply connect
the CAN-BUS box option according to the included wiring-diagram. However, we cannot
guarantee that each and every used function will work, as a lot of vehicle use a lot of different
functions for their remote keys.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zenec ZE-MC294 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zenec ZE-MC294 in the language / languages: English as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info