729841
38
Zoom out
Zoom in
Previous page
1/41
Next page
74 Rev.A 75 Rev.A
REMOVAL WORK AND PREPARATION
INSTALLATION NOTES
NOTE
Make sure that all connectors at the rear of the ZENEC system have sufcient room and are
not bent.
Connectors without a retaining mechanism must be additionally secured with insulating tape.
CAUTION
The installation of the ZENEC system should be carried out by an authorized installer. Specic
knowledge and tools are required to do the installation. Incorrect installation can cause damage
to the vehicle and the ZENEC system.
Correct functioning can only be guaranteed when you use the ZENEC original accessories
included in the kit or those optionally available. The ZENEC system and the original accessories
must under no circumstances be modied or altered in any way. Inappropriate actions can
cause damage to the vehicle and the ZENEC system.
NOTE
The ZENEC system is not compatible with vehicles, which are equipped with a hybrid or electro
drive ex factory.
The ZENEC Z-N328 is equipped with an integrated DAB+ receiver. To make use of this you
will need a suitable DAB antenna (not included in kit) that must be connected to the ZENEC
system.
If the target vehicle is already equipped with an original DAB antenna, it is still possible to use it
in combination with the ZENEC system.
The set of this ZENEC device also contains a 2.4GHz Wi dongle. This dongle can be
connected to the designated USB wire on the device backside.
Software updates to the ZENEC system are installed with a USB memory device. Therefore
when tting the system make sure that the USB connection of the ZENEC system will still be
accessible later (installation of USB extension cable or USB hub).
If you have questions or problems relating to the ZENEC system, please contact the dealer from
whom you purchased it.
NOTE
1. Remove the ignition key and keep it outside the car until the installation is finished.
2. Please wait for ca. 10 minutes until the CAN bus system is completely shut down, before
you start with the deinstallation of the original device.
3. Start with the deinstallation of the original device.
4. Please switch on the ignition only, when all work steps are done and the ZENEC system is
completely mounted.
COMMISSIONING
Make sure that the vehicle is located outside, and that the GPS reception is not adversely affected
by any shadowing (trees, high buildings etc.). Now insert the navigation software SD card supplied
into the microSD card slot of the ZENEC system, and start it in order to establish a sat fix. Make sure
that the vehicle is not moved until the sat fix is established. Now press the NAV button to start the
navigation mode, and choose map view. Once your present location can be seen in the map view the
sat fix has been established. This can take 3 to 5 minutes. You can now use the ZENEC system.
Finally carry out a general functional test and perform the basic and car specific settings (AC, OPS
etc.). Also ensure that no fault warnings appear on the vehicle side.
OVERVIEW INCLUDED
ACCESSORIES
No. Article Qty
1
Main device user manual
1
2 2DIN trim frame 1
3 2DIN metal device mounting cage 1
4 ISO-DIN main harness 1
5 Camera / Reverse Signal / Steering Wheel Control interface (yellow connector) 1
6
4.2 RCA preamp line out + A/V IN (black connector) 1
7
Bluetooth RCA preamp line out (brown connector) 1
8
USB
extension cable
1
9
Parking break wire 1
10
GPS antenna with cable and Fakra connector 1
11
Bluetooth microphone with mounting clip 1
12
Factory radio removal tool 1
13
2.4GHz Wi dongle 1
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zenec Z-N328 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zenec Z-N328 in the language / languages: English as an attachment in your email.

The manual is 13,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Zenec Z-N328

Zenec Z-N328 User Manual - German - 41 pages

Zenec Z-N328 User Manual - Dutch - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info