539676

Zelmer Odyssey 450.0 ST Manual

48
Zoom out
Zoom in
Previous page
1/50
Next page
52
OUTLET FILTER
The vacuum cleaners are equipped with an outlet lter ACF
Microlter or H11 Class HEPA (High Efciency Particulate
Air) lter depending on the type of the vacuum cleaner. The
HEPA lter is a high-quality lter produced from special bers
which are able to stop almost all dust particles. The H11
Class indicates the permeability of the lter. The H11 HEPA
lter stops 95.5% of particles as small as 0.3 micron.
1
In order to replace the outlet lter, open the accessory
compartment.
2
Press rmy the blocking mechanism of the outlet lter
cover and remove the cover out of the vacuum cleaner.
3
Remove the outlet lter cassette, replace the used
cassette with new one. The HEPA lter assure circa 1 year of
effective usage.
4
Place the outlet lter cover back on in such a way that
the three cogs on the lower side of the cover t into the holes
in the vacuum cleaner housing. Next press the lter cover
until the blocking mechanism closes hut. If you do it right,
you will hear a characteristic “click” sound.
Close the accessory compartment.
●
SAFBAG dust bag disassembly/assembly
1
The vacuum cleaner is equipped with safety valve located
in chamber of dust container (bag). It opens automatically
in case of total stopping of suction hose or total stopping of
equipment elements connected thereto, as well as in case
of overll of dust bag. After opening the valve one can hear
characteristic “whirr” sound inside the vacuum cleaner.
2
Switch off the vacuum cleaner by pressing the on/off
button (2).
3
Unplug the appliance.
4
Pull the end of the hose out of the inlet opening of the
vacuum cleaner.
5
Release the front cover fastening (8) and open the
cover.
6
Put the vacuum cleaner in a vertical position (it is easier
to open and put it on its back wheels, while its second half
leans over the front part of the dust container).
7
While holding the bag plate, pull it aside towards the
inside of the dust container, and then pull the bag up.
8
Close the SAFBAG bag cap, as to close the full bag.
Throw it out.
9
Place the plate in the new bag before the sliders and
slide it in along with the screen right down to the bottom of
the container. Unfold the bag. The direction is shown by an
arrow placed on the bag.
10
Close the cover until you hear the characteristic clicking
sound – be careful not to catch the bag.
ATTENTION! Do not start cleaning without an installed
SAFBAG bag.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
F
a) the safety valve activates,
b) the vacuum cleaner operates poorly,
c) the dust bag is full.
Special accessories
The following special accessories may be purchased in retail
outlets:
Zelmer turbobrush (21)
May be used with all types of ZELMER vacuum cleaners. Is
used for an effective vacuuming of carpets and tted carpets.
While using the turbobrush follow the instruction manual.
The use of the turbobrush decidedly increases the
effectiveness of removing brous dirt such as: animal hair,
hair, threads etc. It is practically useful in households with
pets (cats, dogs), where removing the animal hair from the
carpets and oorings is very onerous.
Zelmer electrobrush (22)
Only the electrobrush manufactured by ZELMER may be
used with ZELMER vacuum cleaners. Using other brands of
electrobrushes may cause damage to the vacuum cleaner.
The electrobrush may be used with all ZELMER vacuum
cleaners equipped with the appropriate electrobrush socket.
While using the electrobrush follow the instruction manual.
The electrobrush is especially helpful in cleaning worn out
carpets. Before vacuuming remove all larger elements from
the oor such as: remains of cloth, paper etc. in order to
prevent blocking of the whirling element of the brush.
End of operation cleaning and
maintenance
1
Switch off the vacuum cleaner by pressing the “on/off”
button (2).
2
Unplug the appliance.
3
Wind the cord by pressing the cord rewind button (4).
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4
Disconnect the suction tube from the suction nozzle or
brush.
5
Disconnect the suction tube from the hose. In order
to remove the telescopic tube from the hose handle,
simultaneously press the lock A and pull the tube in the
direction indicated by the arrow.
6
Pull the end of the hose out of the inlet opening of the
vacuum cleaner.
7
The vacuum cleaner may be stored vertically or
horizontally. In order to do so, insert the fastening hook of
the combination brush to the combination brush fastener.
The hose may be attached to the vacuum cleaner, however
you have to make sure that it is not excessively bent during
storing.
8
If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
E
D
… 48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer Odyssey 450.0 ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Odyssey 450.0 ST in the language / languages: English, Polish as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info