539696
35
Zoom out
Zoom in
Previous page
1/38
Next page
39
VC1002-002_v01
Appliance elements
A
1
Cord rewind button
2
Suction power regulation lider
3
ON/OFF button
4
Combination brush fastening
5
Handle
6
Plug and cord
7
Outlet lter cover
8
Bag repletion indicato
9
Front cover handle
10
Suction hose
11
Inlet lter (installed in the vacuum cleaner)
12
“Microlter” outlet lter (installed in the vacuum cleaner)
13
Telescopic suction tube with a fastening hook
14
Reusable bag (1 item)
15
SAFBAG dust bag (1 item)
16
Holder of the bag
17
Small brush
18
Crevice nozzle
19
Small nozzle
20
Switchable combination brush
21
Parquet brush “BNB (additional equipment may be
bought in retail centers)
Preparing the vacuum cleaner
for operation
1
Press the side button on the end of the suction hose.
2
Place the end of the suction hose in the vacuum cleaner.
You should hear a distinctive click, if you do it right.
3
Attach the other end of the hose (the handle) to the
suction tube.
4
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
5
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
6
To clean hard surfaces wooden oors, plastic oors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the gure .
7
Pull the plug and cord (6) out of the vacuum cleaner.
Whilepullingoutthecord,payattentiontothe
yellowstripewhichsignalstheendofthecord.
Furtherattempts(pullingoncord)mayresultin
damagingthecord.
8
Plug in the appliance.
Before operation make sure that the bag is installed in the
vacuum cleaner chamber and that inlet lter and the outlet
lter is installed in the appliance.
B
9
Switch on the vacuum cleaner by pressing the “on/off”
button (3).
10
The vacuum cleaner is equipped with an electronic
suction power controller. The power adjustment is done by
means of a slider. By shirting the slider in a given direction,
you decrease or increase suction.
Filter disassembly
Before changing the lters make sure that the vacuum
cleaner is switched off and unplugged from the mains
supply.
INLET FILTER
1
Open the front cover handle (9).
2
Pull the bag out of the chamber (see p. E).
3
Remove the inlet lter (11) out of the housing.
4
If the inlet lter (11) is dirty, it may be rinsed with running
water. Remember to dry the lter, before its reinstallation.
Duetosafetyreasons,itisvitalnevertoinstall
adampinletlter(11).
5
Install a new/the rinsed inlet lter (11), making sure that
the whole lter is in the socket.
6
Insert a bag into the vacuum cleaner chamber (see
p. E).
7
Close the front cover of the vacuum cleaner.
Thedamagedinletltershouldbereplacedwith
anew,genuinemanufacturedproductonly.
OUTLET FILTER „MICROFILTER”
1
Press the lock and open the cap of the outlet lter, then
pull the cap out of the cleaner.
2
Take the used outlet lter out (12).
If the outlet lter
(12) is dirty wash it in running water.
Remember to dry the lter before putting it into the
cleaner.
3
Put new/washed lter into the cleaner.
Duetosafetyprecautionsneverputwetoutlet
lterintothecleaner.
4
Put the cap so as to two ledges in the lower part of the
cap match the holes in the cleaner body, close the cap by
pressing it until you hear a characteristic “click”.
Damagedoutletltershouldbealwaysreplaced
withaneworiginalone.
C
D
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer Dot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Dot in the language / languages: English, Polish as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info