538924

Zelmer Doris 393 Manual

24
Zoom out
Zoom in
Previous page
1/26
Next page
26 393-119_v01
Technical data
Technical parameters are given on product data plate.
Thickness slice range from 0 to 15 mm
Maximum uninterrupted working time 10 minutes
Break time before repeated use 30 minutes
Noise of device (L
WA
): 75 dB/A
Slicer types 393.5 are build in isolation class II, they do not
require ground.
ZELMER slicers meet the requirements of binding norm.
The device is in agreement with the following directives:
Low voltage electrical device (LVD) – 2006/95/EC. –
Electro-magnetic compatibility (EMC) – 2004/108/EC. –
The device is marked with CE sign on data plate.
Device description (Fig. A)
The food slicer consists of:
Driving system which includes:
1
Body.
2
Table with carriage blockade.
3
Switch button.
4
Regulator with a crank to regulate the thickness of slicing.
5
Circular knife with clamp handle (for mounting the knife
in a drive) made from stainless steel, with serrate edge,
very stiff and hard, which can slice different products with
equally good effect.
and other components:
6
Plastic carriage. The carriage can be easily removed
from slicer table.
7
Clamp, that serves for holding small products. Similarly
to carriage, the clamp protects user’s hand from rotating
knife.
8
Plastics tray, located during slicing next to the slicer, so
that the cut slices can easily lay on it.
Preparing the slicer for work (Fig. B)
1
Put the slicer in a place comfortable to operate it, near
the socket, so that the switch button can be pressed with left
tumb, and a product or the clamp can be held in right hand.
Kitchen countertop should be dry and have good grip. The
slicer cannot move while working.
2
Set the regulator in a position corresponding to thickness
of slicing 0 mm.
3
Press the button on the side of slicer’s body.
ZELMER Slicer types
Slicer type
Regulator Tray Table Carriage
Material Aluminium Material
Chromium-nickel
sheet
Constant Folding
Oblique
constant
Chromium-
nickel sheet
Material
393.5 NP
+ – + – – + – + –
4
Put the table horizontally, grooved surface up.
5
Lift the table at an angle of 45° and insert its left arm so
that the bolt comes into body opening.
6
Then slide the right arm into oblique guide.
7
Let the button go and lower the table until the level.
8
Install carriage, fastening the handle to table guides
(special limiter prevents the carriage from falling out of the
table).


9
Put the product on the carriage.
10
Install the clamp on the carriage.
11
Set the required thickness of slicing within the range
0-15 mm using the crank.
12
Put the plug of connecting cord into socket.
Starting the slicer (Fig. C)
1
Press the switch button with left hand until resistance, in
the direction marked on the slicer.
2
After releasing the switch goes back to its original
position and the slicer stops.
3
Pressing the product with right hand move it together with
the carriage (and clamp) from you until the end of carriage
range, move it back and repeat the activity as many times as
many slices you want to have.
Directions for slicing
Put the product on the carriage in such position so as to
●
obtain slices of required shape (e.g. obliquely).
Too big products (which cannot be placed on the
●
carriage) cut into smaller parts, which may be easily
pushed with a clamp, what eliminates the risk of injury
from the knife.
Before slicing cheese wipe the knife with wet cloth
●
(avoiding touching the knife with your hands). During
wiping the slicer must always be disconnected.
Cheese will not stick to the knife.
Approximate thickness of slicing is dened by symbols
●
next to the regulator (bread, cheese, cured meat).
Manufacturer of the slicer recommends slicing products
as follows:
bread into slices about 10 mm thick, ●
cheese and semi-soft cured meats into slices about ●
3 mm,
… 24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer Doris 393 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Doris 393 in the language / languages: English, Polish as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info