Manual Zelmer Ceres VC3300.0 SK (page 62 of 62) (English, Polish)

539654

Zoom out

Zoom in

1/62

66 VC3300-001_v01

Remove the tube of the CYKLON dust container from the

container.

If the tube of the CYKLON dust container (19) is dirty,

it may be rinsed with running water. Before reinstalling the

tube, make sure it is dry.

Insert the rinsed tube of the CYKLON dust container into

the socket of the container in such a way that the protrusion

situated on the ange of the tube is situated in the socket of

the body of the container. The other end of the tube is to be

inserted into the round socket situated on the bottom of the

chamber, where the tube is placed.

Snap the bottom of the CYKLON dust container shut.

Pay attention that the seal on the bottom of the container

remains correctly placed.

Place the emptied CYKLON dust container into the

chamber of the vacuum cleaner. A characteristic “click”

signalizes the container has been properly installed.

Special accessories

The following special accessories may be purchased in retail

outlets:

Parquet brush “BNB” (25)

Is used to clean and polish hard, scratch sensitive surfaces

such as wooden oors, oor panels, parquet, marble, tiles, etc.

Delicate and soft natural bristles ensure maximum vacuum

effectiveness and protects against scratching the cleaned

surface.

After-work procedures, cleaning, and

maintenance

Press the on/off button (4) to stop the vacuum cleaner.

Remove the plug of the cord from the socket.

Wind the cord by pressing the cord winder button (7).

Hold the cord when doing it to avoid tangling the cord up or

letting the plug hit the vacuum cleaner.

Disconnect the telescopic suction pipe from the nozzle or

brush.

Disconnect the telescopic suction pipe from the hose.

Press the button situated on the end of the hose, and

remove the end of the hose from the inlet of the vacuum

cleaner.

The vacuum cleaner may be store in a vertical or horizontal

position. The hose may stay attached to the vacuum cleaner

as long as it is not bent too much during storage.

Horizontal storage:

place the hook of the nozzle brush into the fastening –

of the nozzle brush situated at the back of the vacuum

cleaner, near the entrance of the power cord.

Vertical storage:

place the nozzle brush on the telescopic pipe, –

then insert the hook of the telescopic pipe into the –

fastening situated on the bottom of the vacuum cleaner,

near the front wheel.

Situate the CYKLON dust container with the installed

HEPA inlet lter (16) in the chamber of the vacuum cleaner.

A characteristic “click” signalizes the container has been

properly installed.

 WeadviseyoutoreplacetheHEPAinletlter

(16)withanewoneevery6monthsofuse.

 Do not use the vacuum cleaner without the

HEPAinlet lter(16) installedinthe CYKLON

dust container. If the HEPA inlet lter is not

there,it isimpossibleto situate theCYKLON

dustcontainerinthevacuumcleaner.

FOAM OUTLET FILTER

In order to replace the foam outlet lter (14) press the

fastening on the cover of the lter, and remove the cover of

the lter from the vacuum cleaner.

Pull the handle situated on the frame of the foam outlet

lter (15) to the right, pull the frame aside towards you, and

remove it from the vacuum cleaner.

Remove the foam outlet lter from the frame.

If the foam outlet lter (14) is dirty, you may replace it with

a new one, clean it or rinse it with running water. Before

reinstalling the lter, make sure it is dry.

 Forsafetyreasonsitisunacceptabletoinstall

awetordamagedfoamoutletlter(14).

Place the new/rinsed lter carefully into the frame.

Situate the frame with the foam outlet lter (14) into the

vacuum cleaner, so that both of the fastenings on the right side

are tted into the holes in the body of the vacuum cleaner.

Block the frame from its left side in such a way that the

fastenings of the frame are inserted into the holes in the body

of the vacuum cleaner.

Place the lter cover in such a way that the two

protrusions situated in the lower part of the cover are

inserted into the holes in the body of the vacuum cleaner,

then press the lter cover to snap the fastening in the body

shut. A characteristic “click” signalizes the cover has been

properly installed.

 Donotusethevacuumcleanerwithouttheinlet

ltersandtheouterlterinstalled.

 Always replace damaged lters with original,

brandnewones.

TUBE OF THE CYKLON DUST CONTAINER

It is necessary to periodically clean the tube of the CYKLON

dust container.

Remove the CYKLON dust container and empty it, as

described in para. C.

Press the button situated on the CYKLON dust container,

and open its bottom. If the CYKLON dust container is full,

empty it as described in para. C.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Ceres VC3300.0 SK in the language / languages: English, Polish as an attachment in your email.

The manual is 4,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer Ceres VC3300.0 SK Manual

Product: