Manual Zelmer Aquawelt 919.0 ST (page 60 of 66) (English, Polish)

539649

Zoom out

Zoom in

1/66

atomizing nozzle or the large atomizing nozzle until you hear

a characteristic click.

Use the following nozzles for the wet vacuuming and wet

cleaning function or to pick up water: large atomizing nozzle,

small atomizing nozzle or the water pick up nozzle.

Slide the stub pipe valve plug downwards.

Insert the stub pipe of the hose to the valve in the

●

vacuum cleaner housing.

Make sure the stub pipe fastenings snap shut.

●

ATTENTION! In case of difculties in connecting the

above mentioned elements moisten the gaskets e.g.

with technical vaseline, water, etc.

Vacuum cleaner functions

TRADITIONAL CLEANING WITH SAFBAG DUST BAG

Press and hold the container lid opening button (2) and

lift the container lid.

Remove the water lter module from the container

(ltration unit and partition).

Insert the dry ltration module with the SAFBAG (21)

dust bag to the container.

Prepare the vacuum cleaner for operation according

●

to section B.

The vacuum cleaner will by default begin operation at

the medium power range. 3 diodes will light on the power

level indicator (9). Set the desired power value (this function

is only available in vacuum cleaners type 919.0) by pressing

the power adjustment buttons +/- (8).

ATTENTION! The vacuum cleaner is equipped with

a power limiting function should the inlet opening be

clogged or the SAFBAG dust bag full. It is manifested

by a pulsing limitation of the motor power and the

lighting up of the clogged air inlet indicator (11) while

the vacuum cleaner is operating at full power (type

919.0). In such a case switch off the vacuum cleaner

by pressing the on/off button (7), unplug the appliance

and clear the tubes or replace the SAFBAG dust bag.

SAFBAG dust bag disassembly/assembly

Remove the dry ltration module with the SAFBAG

●

(21)

dust bag from the container.

Pull the SAFBAG dust bag interlock fastening and pull

the interlock aside.

Pull the fastening which attaches the SAFBAG dust bag

to the basket to release the dust bag plate.

Remove the dust bag.

Insert the SAFBAG dust bag according to the arrow

printed on the bag so that the lower part of the bag plate is in

the slot of the housing. Press the upper part of the bag plate

to the fastening until you hear a characteristic click and close

the SAFBAG dust bag interlock.

Insert the dry ltration module with the SAFBAG

●

(21)

dust bag to the container.

VACUUM CLEANING WITH THE USE OF THE

WATER FILTER MODULE

Press and hold the container lid opening button (2) and

lift the container lid.

Insert the partition to the grooves in the container so that

the shutters are directed downwards. Make sure the partition

is correctly mounted in the container i.e. the partition ns

should cover the protrusion in the container.

Fill the container with 1,3–1,5 liter of water. The water

level should be in the range marked on the wall of the

container.

ATTENTION! Do not operate the appliance with an

empty container while vacuum cleaning with the use

of the water lter module.

Cover the container with the lter unit.

Prepare the vacuum cleaner for operation according

●

to section B.

The vacuum cleaner will by default begin operation at the

●

medium power range. 3 diodes will light on the power

level indicator (9). Set the desired power value (this

function is only available in vacuum cleaners type 919.0)

by pressing the power adjustment buttons +/- (8).

ATTENTION! Do not operate the appliance for too long

without replacing the water in the container.

WET VACUUMING AND WET CLEANING

Before using the wet cleaning function thoroughly vacuum

the surface to be cleaned.

Before operating the vacuum cleaner make sure the container

is empty and the water lter module and the lters are clean.

Press and hold the container lid opening button (2) and

lift the container lid.

Remove the container together with the water lter

module (lter unit and partition) from the vacuum cleaner.

Remove the cleaning liquid container (23) by pulling it by

the handle and lifting it upwards.

Open the inlet plug and ll the cleaning liquid container

(23) with the cleaning liquid (the solution of cleaning powder

and water) in the amount indicated below:

Dissolve the content of the bag in a separate container

●

in 1,5 l of warm water with the maximum temperature

of 50°C. The maximum capacity of the cleaning liquid

container is 1,7 l.

Close the inlet plug of the cleaning liquid container

●

Insert the cleaning liquid container (23) back to the

previous position and press the container to x it correctly

(proceed in the reverse order as in case of removing the

container).

Insert the container together with the water lter module

(lter unit and partition) to the vacuum cleaner.

In order to protect from the foam formation or if foam

forms during the cleaning process, use the anti-foam

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer Aquawelt 919.0 ST in the language / languages: English, Polish as an attachment in your email.

The manual is 5,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer Aquawelt 919.0 ST Manual

Product: