539098
76
Zoom out
Zoom in
Previous page
1/78
Next page
80 481-017_v01
enables recalculation of weighted product between these units
displaying it in „g”, „kg” or „lb” after next pressing of the button.
6
Put the weighted product into the rotating bowl and read
its weight in selected units. When the scope of weighting
(3 kg) is exceeded it is indicated by displaying of
symbol
7
The tarring knob TARE enables weighting next added
products without necessity to empty the bowl within the
scope of weighting (total sum of all ingredients max.
3 kg). After pressing TARE knob the display shall indicate
or (depending on selected units) and „TARE”
inscription shall be displayed.
Removing the motor and/or bowl and/or other
weighted product out of the base with scales,
when the scales is switched on with a motor
and/or bowl and/or other weighted product,
shall result in displaying their weight and
“-” symbol. In such case it is impossible to
tare the scales with TARE button, in order
to reset the display it is necessary to press
ON/OFF switch.
When you nish weighting switch off the scales:
with ON/OFF button (next to the display), when you
scheduled further weighting after a short break
with the blocking knob, turning it to OFF, when you do
not plan further weighting, you want to start the motor on
the base or you nish work with the base.
In case you want to switch off the scales with
ON/OFF switch when the display shows other
value than or it is necessary to
press the ON/OFF switch twice.
If the scales does not react for double pressing
the ON/OFF switch, it is necessary to switch it
off (restart it) with blocking knob turning it to
OFF position (for approximately 2 sec.), then
switch it on with the blocking knob again (ON
position) and continue weighting.
Battery saving
The low battery is indicated by displaying for
approximately 1 sec, than the scales shall switch off.
Pressing ON/OFF switch makes the ” gures to be
displayed again for approximately 1 sec.
The scales is equipped with battery saving mode:
blue highlight of the display is switched off automatically
after 40 seconds, when the display indicates all the time
the same weight or no switch was pressed. To restart
the highlight press any switch or add (remove)
minimum 8 g of weighted product in one go.,
the scales is switched off automatically after 100 seconds,
when the display indicates all the time the same weight
or no switch was pressed, restarting after pressing
ON/OFF switch.
After operation with the base, always switch off the scales
with the blocking knob turning it into OFF position.
Remove the worn batteries from the appliance
immediately. It prevents leakage of discharged batteries.
OPERATING THE MINI FOOD PROCESSOR
The appliance characteristics
ZELMER hand blender equipped with mini food processor
is intended for chopping meat, cheese, nuts, onion, garlic,
carrot, roll, etc.
Mini food processor preparation and operation
(g. J)
Before assembling and disassembling of the
mini food processor cover, make sure that
the power supply cord is unplugged from the
mains supply outlet.
Wash the parts in contact with processed product before
rst usage.
Operate the mixer so, that the closed/open markings
located on the appliance are well visible.
1
Place the base
40
on a at, hard and dry surface.
2
Press the mini food processor container
39
into the
base
40
.
Before each usage of the mini food processor knife,
remove the cover out of the blades.
3
Place the mini food processor blade
39
inside the
container
36
so, that the spindle protruding from the
container got into the inlet of the blade.
4
Place the processed products inside the container
39
without exceeding MAX level.
5
If necessary, insert the limiting ring
36
on the
blade
34
*.
6
Screw the lid
32
of mini food processor with the blender
motor until you can feel it is blocked (clockwise).
Further excessive turning the lid of mini food
processor can lead to damage.
7
Insert the mini food processor cover
39
including the
motor, on the container
32
placing the protrusions in the
container grooves and turn the cover (clockwise), until you
can feel it is blocked.
8
Insert the plug of the power supplying cord into the mains
supply outlet.
9
Switch on the appliance and set the required speed
10
After operation switch off the appliance and unplug it
from the mains supply outlet.
Disassembling of the mini food processor shall be
executed reverse to its assembling.
* The limiting ring is useful for chopping parsley or roll pieces
(dry or fresh) intended for breadcrumbs to prevent spreading
the product all over the container.
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 481 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 481 in the language / languages: English, Polish as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info