540093
28
Zoom out
Zoom in
Previous page
1/32
Next page
28 GW39-008_v01
Outline and parts of the hair clipper (Fig. A)
1
Cutting head
2
Cutting length adjustment knob
3
On/OFF switch
4
LCD display
5
Battery rechargeable
6
Loading socket
7
Attachments (4-6; 10-12; 16-18; 22-24; 28-30 mm)
8
Power supply
9
Cleaning brush
10
Lubricating oil for blades
11
Comb
12
Scissors
LCD display
A
percentage charging level indicator
B
graphical battery charging level indicator
C
mains supply connection indicator
Handling and operation of hair clipper
OPERATION WITH POWER SUPPLY ADAPTOR
At rst insert the adaptor plug into the device and then
insert the adapter plug into the mains supply outlet. In mains
supplied mode the device is ready for use.
LOADING ACCUMULATORS AND CORDLESS
OPERATION
Load the device minimum 16h before rst usage and
when 2–3 next loadings.
Make sure the appliance is switched off before charging.
The process of battery (installed in the trimmer) charging
lasts approximately 2 hours.
The trimmer can work approx. 60 minutes with fully
charged batteries.
Insert the ending of the power supply to the trimmer
charging socket (6),
Insert the plug of the power supply in the mains
supply outlet. The percentage and graphical
charging level indicators show the charging process
advancement (ashing).
When the battery is fully charged, the LCD display
(4)
indicates 100 and it is highlighted in blue.
When the battery charging level decreases below 20, the
graphical battery charging level indicator (B) and mains
supply connection indicator (C) start ashing.
When the battery is almost empty, the display colour
changes into red. Connect the trimmer to the mains supply.
The hair clipper accumulator obtains optimum power
after three cycles of loading and unloading. Ten hours
is enough for next loading. In order to provide long life
of accumulators, they should be completely unloaded
before loading.
COMB ATTACHMENTS INSERTING / REPLACING
Select the attachment according to the length of cutting.
Insert appropriate attachment into the sides of the device.
The protrusions shall be locked inside small holes (see
the gure beside) on left and right sides.
Replace one attachment removing it and inserting
another as described above.
In order to remove an attachment bent one side of assembled
attachment gently and then move it up.
Move the cutting length adjustment knob
(2), to increase/
reduce the hair cutting length. The possible hair cutting
length is indicated on each attachment (i.e. 4–6 mm).
USING THE TRIMMER FOR HEAR CUTTING
Cut the hair for demanded length in stages, start form
bigger length.
Insert an appropriate attachment
(7).
Set the desired length of hair/beard cutting with cutting
length adjustment knob (2).
Start up the hair clipper pressing in ON/OFF button
(3).
Cut only small areas.
Move the clipper slowly along hair.
Hold the device so, that the comb attachment is laid at.
Always start the cutting from the neck upwards or from
the forehead and temples upwards to the top of head.
CUTTING HAIR WITHOUT ATTACHMENT
WARNING: The cutting head (1) is very sharp. Injury
hazard!
Cutting without attachment makes possible to trim the
contour, hair line and whiskers as well as neck shaving.
Turn the device so, that the back part was directed
upwards.
Place the edge of the cutting head
(1) without comb
attachment on desired length of bristle hairline.
Move down the clipper in operation.
Cleaning and maintenance
Start the device pressing in ON/OFF button
(3).
Always switch off the hair clipper and unplug the adaptor
from the mains supply outlet before cleaning and
maintenance.
Remove the comb attachment from the hair clipper.
In order to remove cutting head press the cutting head
blade (1) forward with your thumb, in order to release it
from the frame (Fig. C).
If necessary, rinse the plastic comb attachments under
running water, and then dry them thoroughly.
Remove the remains of hair from the cutting head
(1)
with attached cleaning brush (VII).
Insert the protrusion of cutting head
(1) back into the
locking hole in the frame of cutting head.
Press gently the cutting head
(1) in, until you hear
a clicking sound of locking.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 39Z017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 39Z017 in the language / languages: English, Polish as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info