Manual Zelmer 39Z014 (page 47 of 48) (English, Polish)

540098

Zoom out

Zoom in

1/48

When the accumulators are fully loaded, 5 diodes glow. Whereas, one diode glows, it means that the accumulator should be unloaded soon. –

The hair clipper accumulator obtains optimum power after three cycles of loading and unloading. Ten hours is enough for next loading. In order to –

provide long life of accumulators, they should be completely unloaded before loading.

3. Using the clipper for hair cutting and thinning

TIP: Cut the hair for demanded length in stages, start form bigger length.

Insert an appropriate attachment (III, IV, V, VI, VII, and VIII). –

Set the desired length of hair/beard cutting with cutting length adjustment knob – (2).

Start up the hair clipper pressing in ON/OFF button – (4).

Cut only small areas. –

Move the clipper slowly along hair. –

Hold the device so, that the comb attachment is laid at. –

Always start the cutting from the neck upwards or from the forehead and temples upwards to the top of head. –

In order to thin hair insert the thinning attachment (III) on cutting head.

You can reduce the hair volume with this feature. It provides a modern, changed look without the change of hair length.

4. Cutting hair without attachment

WARNING: The cutting head (1) is very sharp. Injury hazard!

You can cut the hair in uniform length of 1–2 mm without comb attachment.

For clipping the hairline of bristle and whiskers, neck shaving:

Move the hair clipper slowly along hair. –

Turn the device so, that the back part was directed upwards. –

Place the edge of the cutting head – (1) without comb attachment on desired length of bristle hairline.

Move down the clipper in operation. –

5. Comb attachments inserting/replacing

You can select one of six attachments (See: Outline and parts of hair clipper):

Select the attachment according to the length of cutting. –

Insert appropriate attachment into the sides of the device. The protrusions shall be locked inside small holes (see the –

gure beside) on left and right sides.

Replace one attachment removing it and inserting another as described above. –

In order to remove an attachment bent one side of assembled attachment gently and then move it up. –

Move the cutting length adjustment knob – (2), to increase/reduce the hair cutting length. The possible hair cutting length

is indicated on each attachment (i.e. 4–6 mm).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 39Z014 in the language / languages: English, Polish as an attachment in your email.

The manual is 0,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Zelmer 39Z014 Manual

Product: