538877

Zelmer 332.2 Crystal Manual

18
Zoom out
Zoom in
Previous page
1/18
Next page
20
Technical data
The technical parameters are given on the data plate of the
product.
1 liter capacity.
Zelmer electric kettles are built in I class insulation and they
are equipped with supplying cord with grounding wire and
grounding plug.
The ZELMER kettle meets the requirements of the standards
in force.
The appliance is compliant with the requirements of the
following directives:
The Low Voltage Directive (LVD) – 2006/95/EC. –
Electromagnetic Compatibility (EMC) – 2004/108/EC. –
The product is afxed with a CE Mark on the data plate.
Structure of the kettle (Fig. A)
1
Base of the kettle
2
Casing
3
Water level indicator
4
Spout
5
Lid
6
Handle
7
On/off button
8
Control light
9
Supplying cord
10
Storage space for the connecting cord
11
Anti-deposit lter
12
Base
Preparation of the electric kettle for
operation
Before the rst use, wash the kettle inside
(for washing instructions see “Cleaning and
maintenance”), ll it with water up to the “max”
level, and let it boil four times (use fresh water
each time) and wash again.
Operating instructions of the electric kettle
(Fig. B)
1
Open the lid (5).
2
Place the lter (11) in the kettle – if it was taken out
before.
3
Fill the kettle up with the desired amount of water (the
level is visible on the indicator (3)).
Do not boil the water if it is below the minimum
level or beyond the maximum level on the
indicator (3).
4
Close the lid.
5
Place the kettle on the power base (12).
6
Put the plug of the connecting cord into a mains socket
with an earth pin – the upper part of the kettle body will
light up.
7
Turn the kettle on by pressing the lever (7) – the indicator
light will come on.
8
The kettle switches off automatically when the water
has reached the boiling point, the lever switch returns to its
starting position – the light comes off.
If further use of the kettle is anticipated, it is not necessary
to remove the plug of the connecting cord from the power
socket.
Be careful not to ll up with water beyond the
nominal capacity when pouring water into the
kettle.
The rising of the water level in the kettle is delayed in relation
to the speed of pouring the water. It is caused by the lter
slowing down the speed of the ow. This can be prevented by
pouring the last portions of water extremely carefully before
the water reaches the maximum level on the indicator.
In the event that an empty kettle is switched
on, it will be switched off automatically by
a thermal device.
To switch on the kettle after it has cooled down
(about 15 min), remove it from the base, ll with
water, replace on the base and switch on by
pressing the switch (7). The cooling down of
the kettle can be accelerated by pouring cold
water into the kettle.
Cleaning and maintenance (Fig. C)
Always clean a cold kettle!
1
Remove the plug of the connecting cord from the power
socket.
2
Take out the lter (11).
3
Clean the outside surfaces with a soft cloth moistened
with washing-up liquid.
In order to remove the build-up of hard water lm from the
outside and inside walls of the kettle, wipe them with a cloth
moistened with vineger.
4
Rinse the kettle with fresh water.
Various black-coloured, rusty, milky, etc.
deposits may form inside the kettle and oat on
the water. This is caused by minerals occurring
naturally in water (calcium, magnesium, iron,
etc.). Such discoloration is not caused by faulty
operation of the appliance and does not affect
its use. In case of substantial accumulation of
mineral deposits, proceed as described in the
“Descaling” section.
333-109_v01
… 18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 332.2 Crystal at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 332.2 Crystal in the language / languages: English, Polish as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info