539093

Zelmer 32Z011 Manual

27
Zoom out
Zoom in
Previous page
1/30
Next page
29
Arrange the power supply cord, so that it is not hanging down
the table or counter and it could not be pulled or fastened.
2
Connect the plug of the power supply cord to the power
supply outlet.
Make sure, that before connecting the appliance to the power
supply, the speed control knob (4) is set in position 0.
3
Assemble the blender jug (3) on the motor unit, so that
the symbol on the motor unit (8) is in line with the mark
▼on the jug.
4
Lock the blender jug (3) turning it in clockwise direction,
so that the symbol on the motor unit (8) is in line with the
mark ▼on the jug.
The handle of the blender jug (3) shall be placed on the
right side of the appliance.
5
Put the ingredients into the blender jug (3).
6
Do not ll over 1500 ml mark on the blender jug (3).
If you do so, the ingredients can lift the lid (5) when the motor
is started.
7
Before use of the stand blender, insert the lid (5) onto
the blender jug (3) so, that its protrusion is in line with the
protrusion on the jug.
ATTENTION: Before inserting the lid (5) moisturize the
gasket with water.
8
Insert the lid overlay (1) into the inlet in the lid (5) so, that
the protrusions of the overlay enter the cuts in the lid inlet
and turn it left or right until it moves.
Do not start up the stand blender without the lid
overlay (1), especially when solid ingredients shall be
used. They can be ejected through the inlet.
9
Switch on the mixing by turning the speed control
knob (4) to adequate position (P, I, II).
10
In order to stop the appliance turn the speed control knob
to position 0.
11
P (PULSE) functions
Turning the knob into
●
P (PULSE) position shall cause the
short operation of the appliance with maximum speed for
the time of holding the knob.
Do not operate the appliance for longer than 2 minutes,
●
otherwise it can be overheated.
In case you need to add some ingredients during the
●
stand blender operation, turn and lift the lid overlay (1),
insert new ingredients through the inlet, then replace the
lid overlay (1) and turn it right until it moves.
Make sure, that the added ingredients shall not exceed
●
the volume inside the jug over 1500 ml mark on the
blender jug (3).
After operation
In order to stop the appliance, turn the speed control knob
to position 0.
Hold the motor unit
●
(8) with one hand, catch the jug
handle with the other hand and remove it out of the
motor unit (8) turning it counter-clockwise.
Remove the lid
●
(5) out of the blender jug (3).
Unplug the appliance from the mains supply when not
●
in use.
Cleaning and maintenance (Fig. C)
Clean after operation as soon as possible, to prevent
the pulp accumulation inside the jug (3).
1
Pour approximately 1 liter of water to the blender jug (3)
and start-up the appliance for approximately 30 seconds and
hold the P (PULSE) button.
2
Then empty the blender jug (3), turn it upside-down and
dry.
3
If necessary, clean the jug (3), lid (5), feeder opening
stopper (1) and blades (6) in warm water with wash-up liquid.
Then rinse it under clean running water and dry.
●
If you left the jug for longer time without cleaning and
●
some particles glued to the jug inner, use nylon brush.
We do not recommend cleaning the jug
●
(3), blades (6),
lid (5) and feeder opening stopper (1) in dish washer.
Aggressive cleaning agents applied in such device can
inuence negative the surface conditions.
4
Clean the outsider of the motor housing (8) with damp,
gentle cloth.
ATTENTION: Do not immerse the motor housing (8) in
water or other liquid.
Do not clean the outside of the housing
●
(8) with
aggressive detergents such as emulsion milk or pastes,
etc. They can remove information graphic symbols.
Do not clean the transparent jug
●
(3) with harsh sponges
or clothes.
After washing dry thoroughly all the parts of the
●
appliance.
Disassembling of cutting unit
Remove the plug of the power supply cord from the
●
mains supply outlet.
Empty the blender jug
●
(3).
Remove the lid
●
(5) from the blender jug (3). Turn the
blender jug (3) „upside down” and place on the at and
rm surface.
Hold the blender jug
●
(3) with one hand, and unscrew the
blade unit with the other hand (counter-clockwise).
Carefully remove the blade unit
●
(6) including the
gasket (7).
ATTENTION: The appliance blades are sharp. Handle
them carefully.
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 32Z011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 32Z011 in the language / languages: English, Polish as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info