483713
69
Zoom out
Zoom in
Previous page
1/72
Next page
11. FEHLERBESEITIGUNG
66
Fehler Fehlerbeseitigung
Keine Anzeige am Receiver
Prüfen, ob Netzstecker eingesteckt u. Netzschalter ein ist.
Netzsicherung im Gerät prüfen. (Fachmann)
Kein Bild;
Anzeige am Bidschirm :
„Kein Signal“
"Kein Videosignal"
Prüfen, ob der F-Stecker Massekontakt mit dem Schirm des
Antennenkabels besitzt (am Receiver u. LNB) (s.S. 6)
Prüfen ob AV eingeschaltet ist (bei Scart)
Alle Einstellungen in den Menüs "Antennenkonfiguration" (S.
45) u. "Systemeinstellungen" (S. 43) überprüfen.
Signalpegel gut, aber kein
Empfang
Antenne auf falschen Satelliten ausgerichtet
Kein Empfang beim
Ausrichten der Antenne
evtl. Analogreceiver oder SAT-Finder (HP 480) zum Ausrichten
verwenden.
Analogempfang mit Quattro-
LNB gut, kein Digitalempfang
Anschlußbelegung zwischen LNB und Multischalter prüfen:
V-High => V (22kHz), H-High => H (22kHz)
Bild nur schwarz weiß u.
gerastert über Scart
Im Menü "Systemeinstellungen" Fernsehnorm auf PAL stellen.
(s.S. 43)
Kein Ton
Stummschaltungstaste
auf der Fernbedienung drücken.
Einzelne Programme sind
gesrt
Störung durch Fremdfunk, z.B. Handy-Telefone (stören
Satellitenfrequenzen 11630MHz und 12480MHz)
Ein Programm fehlt plötzlich
1. Das Program hat den Transponder gewechselt. Starten Sie
die Funktion "Programmsuche". (s.S. 37)
2. Die PID-Nummer hat sich geändert. Programmplatz einschal-
ten und mit "Programmsuche" neu absuchen (S.39).
Receiver wurde durch
Fehlbedienung verstimmt
Reset auf Werkseinstellung durchführen (s.S. 51).
Nur ein Satellit bei Multifeed
Anlagen empfangbar
Prüfen, ob Schaltereinstellungen mit der Anlage überein-
stimmen. Reset auf Werkseinstellung durchführen. (s.S. 45; 51)
Bild zu dunkel
Im Menü "Systemeinstellungen" Video Ausgang auf „FBAS“
stellen. (s.S. 44)
Analog-Receiver zeigt nur
noch eine Ebene
DVB Receiver ausschalten
Kein Bild
Scartkabel TypeC verwenden; Pin16 des Scartkabels entfernen
Menü "Systemeinstellungen" Video Ausgang auf FBAS stellen.
Gestörtes Bild durch
rasterartige Bildausfälle
Meldung "Schlechtes Signal"
Schlechtes Empfangssignal, Antenne nachjustieren,
F-Stecker auf festen Sitz prüfen. Eingangspegel mit Inline-
verstärker oder Dämpfungsglied (BM335) anpassen, altes
Kabel nicht bis 2150MHz tauglich.
Uhrzeit stimmt nicht
Anderes Programm einschalten
Lokalzeit im Menü Systemeinstellungen prüfen (s.S. 44)
Kein Bild aber Ton
Radio Betrieb eingeschaltet, Taste „TV/Radio“ drücken (s.S. 16)
Kein Bild
Taste
drücken (Schaltsignal an Pin 8 Ein/Aus) (s.S. 17)
Kein Bild bei terr. Programm
Taste
drücken (Schaltsignal an Pin 8 Ein/Aus) (s.S. 17)
Kein Videotext
Taste
drücken (s.S. 18)
Bei Videotext TV-Bild im
Hintergrund
TV-Scart Kompatibilitätsproblem, Pin 15 in Scartkabel
abtrennen.
Kennwort vergessen
Masterkennwort benutzen (s. Kindersicherung S. 47)
Programme nicht gesperrt
Kennwort einstellen (s. Kindersicherung S. 47)
Gerät schaltet plötzlich aus
Timer ist gesetzt, Im Timer-Menü Timer ausschalten(s.S. 29)
Gerät reagiert nicht mehr
Netzstecker ca. 10 Sek. ziehen
Nur
DX 2000 CI
:
Programme werden nicht
entschlüsselt
Receiver aus- und einschalten, Bedingungen zur Freischaltung
beim Programmanbieter erfragen, siehe auch CI-Funktion S. 53
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zehnder DX 2000 CI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zehnder DX 2000 CI in the language / languages: English, German as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info